First run of tools for the month of June. Pickings haven't been great,
but they have been steady, when the weather cooperates. There are lots
of fresh collectible and usable tools on this list.
PayPal is preferred (if you use it) on all items. It's easier for me to
ship items off of a paid PayPal invoice, especially First Class ones.
Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
---------------------------------------------------
Fresh Squeezings Of The Old Tool Trees
Hand Forged 1 1/4 Cross Peen Hammer Head. Measuring 5" long, the face
is 15/16" square, the peen is 1 3/16" wide, and this weighs 1 lb 4 1/2
oz unboxed. Not signed as to the maker, save for the 4 punch marks
around the top of the eye. This is in reasonably good condition and was
cleaned. There is some light pitting around the peen area, but overall
this is clean. The face has some very light dings and frosting. The
peen has some light pitting. The punched eye is good to go. This ain't
pristine, but tools like this rarely are, and this will get the job
done. $18.00
http://oldetoolshop.com/forsale/june/hammer0614a.jpg
http://oldetoolshop.com/forsale/june/hammer0614b.jpg
http://oldetoolshop.com/forsale/june/hammer0614c.jpg
Big Natural Fine Grit Sharpening Stone. Measuring 8 3/4" long, 2 3/8"
wide at one end, 2 1/2" at the other end, 15/16" thick, and this weighs
2 lbs 2 1/4 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. The face is good other than
some flaws at the one end. This is very slightly (like 1/32" or so)
dished looking from the side, but it's flat looking from the ends.
There are some chips around the edges. The one side and end have some
deep saw marks. The base has some light scratches. This ain't perfect,
but it's a quality older stone that will get the job done. $24.00
http://oldetoolshop.com/forsale/june/sharpeningstone0601a.jpg
http://oldetoolshop.com/forsale/june/sharpeningstone0601b.jpg
http://oldetoolshop.com/forsale/june/sharpeningstone0601c.jpg
TWO Hand Forged Corn Shucking Pegs. The upper one is 3 15/16" long, the
lower one is 4 7/8" long, and they weigh 2 oz unboxed. They both have
the X maker mark and the same end treatment. These are in reasonably
good condition and were cleaned. There isn't much patina other than
some rusting around the holes that I couldn't get to. The tips are both
good. The one has a leather loop, the other one a lace loop, but both
will get the job done. I gotta say, that having sold a bunch of these
guys over the years, that finding a matched pair by the same maker,
rarely happens. $22.00
http://oldetoolshop.com/forsale/june/hfcornpeg0601a.jpg
http://oldetoolshop.com/forsale/june/hfcornpeg0601b.jpg
http://oldetoolshop.com/forsale/june/hfcornpeg0601c.jpg
Carll Patent 1913 6 Inch Adjustable Wrench. Measuring 6" long and this
weighs 6 1/4 oz unboxed. Addison B. Carll of Boothwyn, PA was granted
Pat. No. 1,060,891 on May 6, 1913 for the design of this tool which was
made by the Practical Tools Co. of New York, NY. This is in reasonably
good condition and was cleaned. There is some light patina overall.
The jaw faces have some dings and light wear. The adjuster works and
the jaw is reversible so that this can be used as a pipe wrench as
well. The handle is good. This ain't pristine, but these guys sure do
not show up every day. $22.00
http://oldetoolshop.com/forsale/june/wrench0601a.jpg
http://oldetoolshop.com/forsale/june/wrench0601b.jpg
http://oldetoolshop.com/forsale/june/wrench0601c.jpg
North Bros Yankee No 10 Ratcheting Screwdriver & No 72 Screw Holder.
Measuring 9 3/8" long and this weighs 6 oz unboxed. Zachry T. Furbish
of Philadelphia, PA was granted Pat. No. 593,157 on Nov. 2, 1897 for the
design of the ratchet, and Thomas J. Fegley and George O. Leopold, were
granted Pat. No. 864,633 on Aug. 27, 1907 for the design of the screw
holder. This is in reasonably good condition and was cleaned. The tip
and shaft are good. The screw holder has a little patina down in the
crannies and nooks, but it works just fine. The plating on the ratchet
is good and that works in both directions and the locked position. The
handle has some wear to the original finish, a few dings, and there are
few bits of paint that didn't want to come off. This ain't perfect, but
this is not a very common North Bros tool to say the least. $32.00
http://oldetoolshop.com/forsale/june/yankee0602a.jpg
http://oldetoolshop.com/forsale/june/yankee0602b.jpg
http://oldetoolshop.com/forsale/june/yankee0602c.jpg
Union Tool Co 12 Inch Machinist Combination Square. This weighs 12 1/2
oz unboxed. This is in used but good condition and was not cleaned.
The finish on the head is good, save for a few dings on the curved
area. The level vial is good, the scribe is present, and the locking
tab and nut are good to go. The machined faces have some light scuffs.
The rule also has some very light scuff marks and a hint of staining,
but nothing too bad. All the rulings are readable and the edges and
corners are crispy. This ain't pristine, but it sure ain't bad, and it
will get the job done. $30.00
http://oldetoolshop.com/forsale/june/machinisttool0606a.jpg
http://oldetoolshop.com/forsale/june/machinisttool0606b.jpg
http://oldetoolshop.com/forsale/june/machinisttool0606c.jpg
http://oldetoolshop.com/forsale/june/machinisttool0606d.jpg
http://oldetoolshop.com/forsale/june/machinisttool0606e.jpg
L S Starrett No 1 7 Inch Adjustable Jaw Cut Nippers. This weighs 15 1/4
oz unboxed. This is in reasonably good condition and was cleaned.
There is a little shop patina and a few dings on the sides of the jaws,
but nothing too bad. The jaws are good save for a couple of very tiny
dings and all the screws work. The joint, spring, and handles are all
good to go. This ain't minty, but it is a top quality tool that will
get the job done. $35.00
http://oldetoolshop.com/forsale/june/machinisttool0604a.jpg
http://oldetoolshop.com/forsale/june/machinisttool0604b.jpg
http://oldetoolshop.com/forsale/june/machinisttool0604c.jpg
Vintage Lufkin No 1206 Aluminum 6 ft Zig Zag Rule. This weighs 6 oz
unboxed. This is in decent condition and was not cleaned. There is
some light staining and scuffs on the segments, but all the rulings are
readable and the joints are good with no play. The ends have a little
wear on the corners. This ain't minty, but these guys rarely are. $15.00
http://oldetoolshop.com/forsale/june/rule0601a.jpg
http://oldetoolshop.com/forsale/june/rule0601b.jpg
http://oldetoolshop.com/forsale/june/rule0601c.jpg
Vintage Turnscrew Screwdriver Flat Nut Saw Brace Bit. Measuring 4"
long, the tips are 7/16" across the outside, 1/4" across the inside, and
this weighs 1 1/2 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some frosting and light
pitting on the head. The tips are good. The tang is also good and has
a small notch for a bitstock. This ain't pristine, but these guys sure
do not show up very often. $16.00
http://oldetoolshop.com/forsale/june/bracetool0602a.jpg
http://oldetoolshop.com/forsale/june/bracetool0602b.jpg
http://oldetoolshop.com/forsale/june/bracetool0602c.jpg
THIRTEEN Snell & Craftsman Auger Bits With Canvas Roll. The sizes go
from 4 to 16, the Craftsman bits have red or black tangs, the Snell bits
have orange tangs, and this all weighs 3 lbs unboxed. These are Irwin
pattern bits. These are in reasonably good condition and were cleaned.
There is a little patina there and here, but nothing too bad. Some of
the lead screws have a little rust, but they are all good. The spurs
and cutters are good for the most part, a couple of them will need a
touch up. A couple of the tangs have some dings on the edges, but they
are good to go. The canvas roll looks like it could be military issue.
That has some small holes, a few bits of paint, and the strap is gone,
but overall it's solid. These ain't pristine, but they are quality
tools that will get the job done. $55.00
http://oldetoolshop.com/forsale/june/bracebitset0601a.jpg
http://oldetoolshop.com/forsale/june/bracebitset0601b.jpg
http://oldetoolshop.com/forsale/june/bracebitset0601c.jpg
http://oldetoolshop.com/forsale/june/bracebitset0601d.jpg
http://oldetoolshop.com/forsale/june/bracebitset0601e.jpg
Forged 6 oz Cross Peen Hammer Head. Measuring 4 1/4" long, the face is
1/2" square, the peen is 3/4" wide, and this weighs 6 oz unboxed. Not
signed as to the maker. This is in reasonably good condition and was
cleaned. There are some dings on both sides of the eye, and a few spots
of light pitting, but overall there ain't much in the way of patina.
The face has some light dings and a couple of tiny dings around the
edge. The peen is good. The punched eye has a little crusty on the
inside, but it's good to go. This ain't the fanciest, but it is an
older tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/june/hammer0612a.jpg
http://oldetoolshop.com/forsale/june/hammer0612b.jpg
http://oldetoolshop.com/forsale/june/hammer0612c.jpg
THREE Larger Center Point Brace Bits. The first one is a 1 1/2"
(measured from the point to the spur and doubled) that is just marked
Warranted, an F G Pearson Sheffield 1 3/4", a Schmidt & Mollenhoff 2
1/8", and they weigh 9 1/2 oz unboxed. These are in reasonably good
condition and were cleaned. The first two are clean, the last one has
some light pitting on both sides of the head. The points and spurs are
all good, a couple of the cutters could stand a quick touch up. The
shafts are all straight with no twists. All the tangs are good, but
none are notched for a bitstock. These ain't minty, but these bigger
ones are sure getting few and far between. Just saying. $24.00
http://oldetoolshop.com/forsale/june/bracetool0601a.jpg
http://oldetoolshop.com/forsale/june/bracetool0601b.jpg
http://oldetoolshop.com/forsale/june/bracetool0601c.jpg
Early Small Hand Forged Claw Hammer. Measuring 9 3/8" overall, the head
is 4" long, the face is 1/2" square, the claws are 5/16" wide at the
tips, and this weighs 6 1/2 oz unboxed. Not signed as to the maker.
This is in decent condition and was cleaned. There is some overall
pitting and patina on the head. The face was dressed at some point and
that is good. The claws have some light chipping on the insides. The
handle is hand carved and old, but I can't say if it's original or not.
That has some dings and stains, but it's solid. This ain't pristine, but
these older ones rarely are. $17.00
http://oldetoolshop.com/forsale/june/earlyhammer0602a.jpg
http://oldetoolshop.com/forsale/june/earlyhammer0602b.jpg
http://oldetoolshop.com/forsale/june/earlyhammer0602c.jpg
http://oldetoolshop.com/forsale/june/earlyhammer0602d.jpg
Lixie E Square Nose Bronze Hammer. Measuring 13 1/16" overall, the head
is 3 15/16" long, the faces are 1 1/16" high, 15/16" wide, and this
weighs 2 lbs 2 1/4 oz unboxed. This is in lightly used but good
condition and was not cleaned. The faces have some very light dings,
but nothing too bad. The finish on the head also has a couple of light
dings. The handle has some stains and there is a area under the head on
the front where somebody (NOT ME!) "erased" a user mark, but it's
solid. This ain't minty but it's 1/2 the price of what a new one will
run you. $23.00
http://oldetoolshop.com/forsale/june/hammer0611a.jpg
http://oldetoolshop.com/forsale/june/hammer0611b.jpg
http://oldetoolshop.com/forsale/june/hammer0611c.jpg
Hand Forged Oyster Or Clam Shucker Shucking Knife. Measuring 8 1/8"
long. the b lade is 5/8" wide, the handle is 3/4" square at the top,
11/16" at the end and this weighs 11 3/4 oz unboxed. Not signed as to
the maker. This is in reasonably good condition and was cleaned. There
ain't much in the way of overall patina to fuss about. The blade is
missing a little bit of the tip, but that is an easy fix. The blade is
bent slightly to one side, but that's the way that this was made. Note
the chamfering on the handle, that is something that you don't see very
often on one of these. There is a whisker of mushrooming on the end.
This ain't perfect, but it sure ain't your run of mill one of these guys
either. $26.00
http://oldetoolshop.com/forsale/june/hfclamknife0601a.jpg
http://oldetoolshop.com/forsale/june/hfclamknife0601b.jpg
TWO Union 3 Inch Machinist Spring Calipers. There is a No. 12 inside
caliper measuring 3 11/16", a No. 14 outside caliper measuring 3 15/16"
long, and they weigh 1 1/2 oz unboxed. These are in reasonably good
condition and were cleaned. There is some frosting and staining on the
legs, but nothing too bad. The springs are quite stiff and the tips are
good. Both nuts travel the full distance smoothly. These ain't minty,
but they are quality tools that will get the job done. $20.00
http://oldetoolshop.com/forsale/june/machinisttool0602a.jpg
http://oldetoolshop.com/forsale/june/machinisttool0602b.jpg
http://oldetoolshop.com/forsale/june/machinisttool0602c.jpg
Vintage 3 lb Auto Body Dolly. Measuring 5 1/8" long, 2 7/16" wide, and
this weighs 3 lbs 6 3/4 oz unboxed. Not signed as to the maker. This
is in reasonably good condition and was cleaned. There is a little
overall shop patina. There are some light dings on the upper side, but
nothing too bad. The rest is good to go. This ain't got a fancy name,
but it will get the job done. $16.00
http://oldetoolshop.com/forsale/june/bodytool0602a.jpg
http://oldetoolshop.com/forsale/june/bodytool0602b.jpg
http://oldetoolshop.com/forsale/june/bodytool0602c.jpg
Vintage Dunlap 10 Inch Sweep Brace. This weighs 2 lbs 5 1/4 oz
unboxed. This is in good condition and was not cleaned. There are a
few dots of patina and staining, nothing bad at all. The chuck and jaws
are good and the ratchet works in both directions and the locked
position. The grip and pad have the original finish, there are few tiny
dings, but it's 99.5% present. Both spin freely. This ain't pristine,
but it's pretty darn close. $23.00
http://oldetoolshop.com/forsale/june/brace0601a.jpg
http://oldetoolshop.com/forsale/june/brace0601b.jpg
http://oldetoolshop.com/forsale/june/brace0601c.jpg
http://oldetoolshop.com/forsale/june/brace0601d.jpg
TWO Dunlap No 9-3956 Framing Square Guides. They weigh 2 oz unboxed.
These are in reasonably good condition and were cleaned. Other than a
little frosting on the tops of the screws, there ain't much in the way
of patina. The screws are good and travel the full distance. The
bodies and slots are good to go. These ain't perfect, but they will get
the job done. $14.00
http://oldetoolshop.com/forsale/june/squareguides0601a.jpg
http://oldetoolshop.com/forsale/june/squareguides0601b.jpg
http://oldetoolshop.com/forsale/june/squareguides0601c.jpg
Bevel Side 1/8 Inch Sash Paring Chisel. Measuring 8" from the edge to
the end of the socket, the blade is 5 5/8" long, this is 12" overall,
and this weighs 3 3/4 oz unboxed. Not signed as to the maker, there is
a user name on the back side. This is in reasonably good condition and
was cleaned. The back has a little frosting, nothing too bad. The
sides and top also have a little patina. The socket has some frosting
and I did take a little mushrooming off the end. The handle is a
replacement. That is good save for a few stains and a couple of tiny
bits of paint down in the grain. This ain't pristine, but it will get
the job done. $22.00
http://oldetoolshop.com/forsale/june/chisel0602a.jpg
http://oldetoolshop.com/forsale/june/chisel0602b.jpg
Vintage Goldblatt No 60-311 M7 Brass Bronze Cement Edger. Measuring 5
13/16" long, the face is 2 3/4" wide, and this weighs 1 lb 1 3/4 oz
unboxed. This is in decent condition and was cleaned. The face and
side edge are good save for a little wear. The top does have some
cement residue. The handle has some stains and a number marked on the
side, but it's solid. This ain't minty, but it is a quality tool that
will get the job done. $18.00
http://oldetoolshop.com/forsale/june/cementtool0601a.jpg
http://oldetoolshop.com/forsale/june/cementtool0601b.jpg
http://oldetoolshop.com/forsale/june/cementtool0601c.jpg
http://oldetoolshop.com/forsale/june/cementtool0601d.jpg
Stanley SW No 61 Marking Gage Or Gauge. This weighs 3 1/4 oz unboxed.
This is in decent condition and was cleaned. There is some overall
staining. The beam is straight and has a few light dings from the
screw. The rulings are readable and the point is good. The head has
some dings and a few tiny bits of paint down in the grain. The screw
has a few chips on the sides of the head, but the threads are good.
This ain't pristine, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/june/markinggage0602a.jpg
http://oldetoolshop.com/forsale/june/markinggage0602b.jpg
http://oldetoolshop.com/forsale/june/markinggage0602c.jpg
http://oldetoolshop.com/forsale/june/markinggage0602d.jpg
Early Hand Forged Carpenters Claw Hammer Head. Measuring 4 1/4" long,
the face is 7/8" high, 13/16" wide, the claws are 1 3/16" wide across
the tips, and this weighs 13 oz unboxed. Not signed as to the maker.
This is in fair condition and was cleaned. There is lots of patina
going on this guy. The face has light pitting and a little wear around
the edges. The one claw is shorter than the other one and has a little
mushrooming on the tip. There is some chipping in the center. The
square punched eye is good to go. Pretty and perfect picked up and moved
out of town on this guy a while back, but it is a collectible old tool.
$15.00
http://oldetoolshop.com/forsale/june/earlyhammer0601a.jpg
http://oldetoolshop.com/forsale/june/earlyhammer0601b.jpg
http://oldetoolshop.com/forsale/june/earlyhammer0601c.jpg
I Sorby Cast Steel 1/4 Inch Firmer Carving Chisel. Measuring 3 3/4"
from the edge to the top of the handle, this is 9" overall, and this
weighs 2 1/4 oz unboxed. This is in reasonably good condition and was
cleaned. The back is clean for the first 1 3/8", after that there are
some light dings. The top also has some frosting and a few dots of
pitting. The brass ferrule has a partial check. The handle has some
stains, dings, and a wee bit of mushrooming at the end, but it's solid.
This ain't pristine, but it is a quality tool that will get the job
done. $15.00
http://oldetoolshop.com/forsale/june/chisel0601a.jpg
http://oldetoolshop.com/forsale/june/chisel0601b.jpg
Millers Falls Amidon Pat 1868 Tool Handle. Measuring 7 5/16" long and
this weighs 12 oz unboxed. Charles H. Amidon of Greenfield, MA was
granted Pat. No. 73,279 on Jan. 14, 1868 for the design of the chuck and
jaws used on this tool. This is in reasonably good condition and was
cleaned. The chuck shell has some frosting, but nothing too bad. The
jaws are good and the spring is present. The rose wood handle has some
dings and a few tiny bits of paint down in the grain. The threads on
the cap are good. This comes with 8 of the original bits. A couple of
them have slight bends, and the back of the chisel has a little
frosting, but overall they are good. This ain't minty, but seeing as how
it's at least 130 years old, well it sure ain't bad. $28.00
http://oldetoolshop.com/forsale/june/toolhandle0601a.jpg
http://oldetoolshop.com/forsale/june/toolhandle0601b.jpg
http://oldetoolshop.com/forsale/june/toolhandle0601c.jpg
Uncommon C Hammond Phila Bookbinders Hammer Head. Measuring 6 1/8"
long, the face is 2 1/4" in diameter, the peen is 1 1/2" wide, and this
weighs 1 lb 9 1/4 oz unboxed. This is in reasonable condition for the
age and use and was cleaned. The sides of the head have some light
dings, and there are some deeper ones around the eye on the top and
underside. The face is good, save for some very light dings and the
peen is good as well. I did run a file over some dings along the inside
edges of the eye and that is good to go. This ain't minty, but this is a
very uncommon tool to say the least. $75.00
http://oldetoolshop.com/forsale/may/hammer0516a.jpg
http://oldetoolshop.com/forsale/may/hammer0516b.jpg
http://oldetoolshop.com/forsale/may/hammer0516c.jpg
Blacksmith Hot Cut Chisel Head. Measuring 6 1/2" long, the edge is 1
7/16" high, and this weighs 2 lb 15 3/4 oz unboxed. This is signed but
it's too faint to read, there is the number 400 stamped on there as
well. This is in decent condition and was cleaned. There is some
overall pitting and patina. The striking end was dressed at some point
and that is good to go. The edge could stand a touch up, but it's not
too bad as is. The eye is good save for a little patina down inside.
This ain't pretty or perfect, but it will get the job done. $18.00
http://oldetoolshop.com/forsale/may/blacksmith0503a.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503b.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503c.jpg
Buck Bros Cast Steel 5/8 Inch Gouge. Measuring 5 1/4" from the edge to
the top of the handle, the b lade is 3 13/16" long, 5/8" wide across the
inside of the sweep, this is 11" overall, and this weighs 5 oz unboxed.
This is in reasonably good condition and was cleaned. The inside of the
sweep has some light scratches by the edge and some frosting, but
nothing too bad. The back also has some staining and some spots of
frosting. The handle has a couple of thin checks under the ferrule and
some stains and dings, but it's solid enough to use. This ain't
pristine, but it's a quality tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/may/chisel0512a.jpg
http://oldetoolshop.com/forsale/may/chisel0512b.jpg
Forest City 1 15/16 Inch Boring Machine Auger Bit. Measuring 8 5/8"
long, the cut is 1 15/16" in diameter, the tang is 1/2" in diameter, and
this weighs 1 lb 1/2 oz unboxed. The Forest City Bit & Tool Co was
founded in 1890 in Rockford, IL and the business relocated to Hickory,
NC, in 1957. The mark is a little worn. This is in reasonably good
condition and was cleaned. There is a little staining overall, and a
little bit of light crusty up at the top, but nothing too bad. This
doesn't have a lead screw, just a point but that is good. The cutters
and spurs are ready to work. The tang has a few scuffs and rings, but
it's good to go. This ain't minty but overall it sure ain't bad. $35.00
http://oldetoolshop.com/forsale/may/bracetool0511a.jpg
http://oldetoolshop.com/forsale/may/bracetool0511b.jpg
Vintage 11/16 Inch Gouge. Measuring 9 3/16" from the edge to the end of
the socket, the b lade is 6 5/16" long, 11/16" wide across the inside of
the sweep, this is 12 3/4" overall, and this weighs 6 1/2 oz unboxed.
This is signed but I can't read the company name. This is in decent
condition and was cleaned. The inside of the sweep has some frosting
for the first 1/2 and some light pitting after that. The back has a few
light spots and some staining, but it's clean enough to use if you want
to flip the bevel. The socket has a little pitting and a small void
where it was seamed. The handle is a replacement. That has some
staining and wear, but it's solid. This ain't pretty or perfect, but it
will get the job done. $18.00
http://oldetoolshop.com/forsale/may/chisel0511a.jpg
http://oldetoolshop.com/forsale/may/chisel0511b.jpg
Vintage I Mfg Co Rivet Set or Setter. Measuring 4 5/16" long, the post
hole is 1/8" in diameter, the dimple is 1/4", and this weighs 6 1/2 oz
unboxed. This is in fair condition and was cleaned. There is some
overall pitting and patina. The face has some light pitting, but both
of the holes are good. The striking end had some mushrooming cleaned
off and it's good to go. This ain't pretty or perfect, but it will get
the job done. $14.00
http://oldetoolshop.com/forsale/may/rivetset0502a.jpg
http://oldetoolshop.com/forsale/may/rivetset0502b.jpg
H Disston & Sons D-8 26 Inch 8 PT Cross Cut Saw. Measuring 29" overall,
the blade is 26" long, 2 1/16" high at the toe, 6 3/16" high right in
front of the tote, this is sharpened to 8 PT CC, and this weighs 1 lb 10
oz unboxed. This was made by Disston between 1917 and 1940. This is in
reasonably good condition, the only cleaning was to wipe some gunk off
the blade and to put some wax on the tote. The blade has some staining
and a few spots of light pitting and rust etching, but nothing too bad.
All the teeth are present and this is sharp. There is a very slight
bend (like 1/16" at the center) looking down the edge, which is usual
for this length of saw. The tote has almost all of the original
finish. There are some dings, and a few bits of paint, but it's solid.
This ain't minty, but it's a solid tool that will get the job done. $35.00
http://oldetoolshop.com/forsale/may/saw0501a.jpg
http://oldetoolshop.com/forsale/may/saw0501b.jpg
http://oldetoolshop.com/forsale/may/saw0501c.jpg
http://oldetoolshop.com/forsale/may/saw0501d.jpg
http://oldetoolshop.com/forsale/may/saw0501e.jpg
L S Starrett No 39 12 Inch Machinist Lock Joint Inside Caliper.
Measuring 12 9/16" long (from the tips to the top of the joint) and this
weighs 10 1/4 oz unboxed. This is in reasonably good condition and was
cleaned. There are a few small spots of pitting on the legs and a
little oil staining around the joint, but nothing too bad. The joint is
good and the fine adjuster works. The tips are also good other than a
little patina. This ain't minty, but it sure ain't got the price tag of
a new one either. Look it up. $30.00
http://oldetoolshop.com/forsale/may/machinisttool0508a.jpg
http://oldetoolshop.com/forsale/may/machinisttool0508b.jpg
FIVE Vintage Brace Tools. There is a square tapered reamer, 4 3/4"
overall, 5/16" wide at the start of the tang, an octagon tapered reamer,
5 1/2" overall, 3/8" wide at the start of the tang, a 1/2" metal boring
bit, 4" overall, a 5/16" spoon bit, 7" overall, a 3/8" quill bit, 6
5/16" overall, and they weigh 7 1/2 oz unboxed. These are in reasonably
good condition and were cleaned. There are some spots of pitting, the
metal boring bit has the most, but overall nothing too bad. The edges
on the reamers and the spoon and quill bits are all good. Three of the
tangs are notched for a bitstock. These ain't pristine, but they are
quality older tools that will get the job done. $22.00
http://oldetoolshop.com/forsale/may/bracetool0507a.jpg
http://oldetoolshop.com/forsale/may/bracetool0507b.jpg
http://oldetoolshop.com/forsale/may/bracetool0507c.jpg
http://oldetoolshop.com/forsale/may/bracetool0507d.jpg
Vintage .370 Round Ball Blackpowder Bullet Mold. Measuring 4 13/16"
long, the cavities are .370 inch in diameter, and this weighs 1 3/4 oz
unboxed. Not signed as to the maker. This is in decent condition and
was cleaned. There is some light patina and some scuff marks left over
from when this was made. The cavities are good. There is a whisker of
light showing when they are closed. The joint is good as are the sprue
cutters. The handles have a bit of bend to them, but that won't affect
this being used. This ain't minty, but it sure ain't getting any easier
to find these guys. $30.00
http://oldetoolshop.com/forsale/may/bulletmold0501a.jpg
http://oldetoolshop.com/forsale/may/bulletmold0501b.jpg
http://oldetoolshop.com/forsale/may/bulletmold0501c.jpg
Vintage Hand Forged Shipbuilders Lipped Adze Head. Measuring 10 1/4"
long, 4 13/16" wide across the outside of the edge, the steel bit is 2
3/8" deep at the center, and this weighs 2 lbs 1/4 oz unboxed. This is
signed but I can't read the mark. This is in fair condition and was
cleaned. There is some overall pitting and patina. The steel bit also
has some pitting, some of it deep. The edge will need some work. The
hammer poll is fairly good,s save for a little mushrooming on the top.
The eye has some crusty on the inside, but it's solid with no cracks
that I can see. This ain't pretty or perfect, but these guys sure have
been hard to come by of late. $30.00
http://oldetoolshop.com/forsale/may/adze0501a.jpg
http://oldetoolshop.com/forsale/may/adze0501b.jpg
http://oldetoolshop.com/forsale/may/adze0501c.jpg
http://oldetoolshop.com/forsale/may/adze0501d.jpg
Small Planishing Hammer For Light Metal Work. Measuring 8" overall, the
head is 4" long, the faces are 1/2" high, 5/8" wide, and this weighs 7
oz unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. The head has some light patina and scuffs
left over from when it was made. Both faces are very slightly convex.
The one face is good, the other one has a ding on the one side and some
very light pitting. The eye is good. The handle was somebody else's
idea of a good time, but it will get the job done. This ain't minty,
but it will get the job done. $22.00
http://oldetoolshop.com/forsale/may/hammer0510a.jpg
http://oldetoolshop.com/forsale/may/hammer0510b.jpg
http://oldetoolshop.com/forsale/may/hammer0510c.jpg
H Boker Lancashire Pattern 4 Inch Outside Caliper. Measuring 4 7/8"
long, the tips close down to 5/16", and this weighs 1 3/4 oz unboxed.
This is in reasonably good condition and was cleaned. There are some
stained spots, some scuffs on the legs, and a little pitting on the
tips. There is a user name on the one side and initials on the other.
The spring is really strong and the screw travels the full distance.
The tips, as noted, don't close down tight, but that's the way that this
guy was made. This ain't pristine, but it is a quality tool that will
get the job done. $22.00
http://oldetoolshop.com/forsale/may/divider0501a.jpg
http://oldetoolshop.com/forsale/may/divider0501b.jpg
http://oldetoolshop.com/forsale/may/divider0501c.jpg
L S Starrett No 83 6 Inch Yankee Pattern Machinist Divider. Measuring 6
3/4" long (from the tips to the top of the spring and this weighs 3 oz
unboxed. This is in decent condition and was cleaned. There is some
overall frosting on the legs, a spot of light pitting on the one leg,
and a small patch on the spring. The spring and tips are good. The
screw travels the full distance smoothly. This ain't minty but it will
get the job done. $22.00
http://oldetoolshop.com/forsale/may/machinisttool0507a.jpg
http://oldetoolshop.com/forsale/may/machinisttool0507b.jpg
http://oldetoolshop.com/forsale/may/machinisttool0507c.jpg
Vintage Lever Style Piano Tuning Wrench Or Key. Measuring 12" long, the
head is 2 15/16" wide, the wrench holes are 5/16" by 1/4" at the ends,
and this weighs 9 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. There are some spots of
light pitting on the head and there are some dings on the shaft. The
wrench heads are good with no cracks. The rose wood handle does have a
thin check on one side, but it feels solid enough. There are some dings
as well. This ain't pristine, tools like this got used hard and this is
not a commonly found style for one of these. $35.00
http://oldetoolshop.com/forsale/may/pianokey0501a.jpg
http://oldetoolshop.com/forsale/may/pianokey0501b.jpg
http://oldetoolshop.com/forsale/may/pianokey0501c.jpg
More Fresh Goodes
Early P S Stubs Wing Compass Or Divider. Measuring 9 1/16" long and
this weighs 11 oz unboxed. This is in decent condition and was
cleaned. THere is some overall frosting and some spots of light
pitting. The 3 finger (2 + 1) joint is a little stiff, but it does
work. The locking screw has a very slight bend along the threads, but
it also works and was oiled. The legs are a little bent, but the tips
are good. This ain't pristine but it is a collectible early tool. $38.00
http://oldetoolshop.com/forsale/may/earlydivider0501a.jpg
http://oldetoolshop.com/forsale/may/earlydivider0501b.jpg
http://oldetoolshop.com/forsale/may/earlydivider0501c.jpg
http://oldetoolshop.com/forsale/may/earlydivider0501d.jpg
Early Hand Forged Dough Pumpkin Scraper. Measuring 5" long down the
center, the head is 5 15/16" wide, 2" high at the center, and this
weighs 7 oz unboxed. There is a touchmark with the initials B L T on
the inside at the start of the handle. My thoughts are that this is of
18th Century vintage. Somebody called this a pumpkin scraper, but it
does look like a dough scraper. Take your pick. This is in decent
condition and was cleaned. There is lots of patina, pitting, and what
have you. The edge is worn but that comes with old age and hard work,
eh? The head area is good with no cracks that I can see. The handle is
solid. This is one of those items that rarely shows up any more. $80.00
http://oldetoolshop.com/forsale/may/earlyscraper0501a.jpg
http://oldetoolshop.com/forsale/may/earlyscraper0501b.jpg
http://oldetoolshop.com/forsale/may/earlyscraper0501c.jpg
http://oldetoolshop.com/forsale/may/earlyscraper0501d.jpg
http://oldetoolshop.com/forsale/may/earlyscraper0501e.jpg
Palmer Folding Handle 10 Inch Draw Knife. Measuring 19" overall, the
blade is 10" long, 1 3/8" wide across the edge, and this weighs 1 lb 7
3/4 oz unboxed. This is in good condition and was cleaned. The back is
good other than a small spot of pitting up at the top. The front also
has a few small spots as well. The top is good and was never struck.
The handles are good and have almost all of the original finish. The
handle screws work and were oiled. This ain't minty but it will get the
job done. $55.00
http://oldetoolshop.com/forsale/may/drawknife0501a.jpg
http://oldetoolshop.com/forsale/may/drawknife0501b.jpg
http://oldetoolshop.com/forsale/may/drawknife0501c.jpg
Early Hand Forged Eel Gig Head. Measuring 8 13/16" long, 3" wide across
the outsides of the tines, and this weighs 11 1/4 oz unboxed. Not
signed as to the maker. This is in decent condition and was cleaned.
There is some overall patina. The tips of the tines were dressed
recently, but the toothing on the sides is worn. The toothing on the
tang is fairly good. These guys are sure getting hard to come by, at
least around these here parts. $30.00
http://oldetoolshop.com/forsale/april/hfeelgig0401a.jpg
http://oldetoolshop.com/forsale/april/hfeelgig0401b.jpg
http://oldetoolshop.com/forsale/april/hfeelgig0401c.jpg
Vintage Forged 1/2 lb Straight Peen Hammer Head. Measuring 4 1/2" long,
the face is 9/16" in diameter, the peen is 11/16" high, and this weighs
8 oz unboxed. Not signed as to the maker. This is in decent condition
and was cleaned. There is some overall light pitting and patina. The
face also has some pitting and a tiny chip off the edge. The peen is
good other than some light pitting. The eye is good. This ain't minty
but it is a neat smaller hammer that will get the job done. $20.00
http://oldetoolshop.com/forsale/may/hammer0507a.jpg
http://oldetoolshop.com/forsale/may/hammer0507b.jpg
http://oldetoolshop.com/forsale/may/hammer0507c.jpg
Stanley No 25 TB 8 Inch Adjustable Bevel Square. This weighs 3 1/2 oz
unboxed. This is in reasonably good condition and was lightly cleaned.
The blade has a few small spots of rust and some scratches but still has
the original plating. The edges and corners are crispy. The handle has
some staining along the one edge and side but also has the original
finish. The locking nut and screw do their jobs. This ain't pristine
but it will get the job done. $16.00
http://oldetoolshop.com/forsale/may/square0502a.jpg
http://oldetoolshop.com/forsale/may/square0502b.jpg
http://oldetoolshop.com/forsale/may/square0502c.jpg
Vintage 10 oz Straight Peen Hammer. Measuring 12 1/2" overall, the head
is 3 3/16" long, the face is about 5/8" wide, 3/4" high, the peen is 1"
high, 5/16" wide, and this weighs 10 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There is some
pitting and patina on the head. The face and peen were dressed by
somebody else. They didn't do a great job, but I'm sure that they are
better than they were. They both have some chipping on the sides. The
handle is old and could be the original one. That has some roughness
under the eye and the usual stains but it feels solid enough. This
ain't pretty or perfect but is is neat looking hammer that will get the
job done. $17.00
http://oldetoolshop.com/forsale/may/hammer0504a.jpg
http://oldetoolshop.com/forsale/may/hammer0504b.jpg
http://oldetoolshop.com/forsale/may/hammer0504c.jpg
Blacksmith Project 1 3/4 lb Cross Peen Hammer Head. Measuring 4 15/16"
long, the face is 1 1/4" by 1 5/16" square, the peen is 1 1/2" wide, and
this weighs 1 lb 14 oz unboxed. Marked as shown. This guy was fresh
from the womb and still has the umbilical cord attached, but it picked
up some rust and I dusted it off a bit. The face and peen will need
some work and the eye is good to go. This is what it is, but with some
time and cussing it will get the job done. $15.00
http://oldetoolshop.com/forsale/may/hammer0502a.jpg
http://oldetoolshop.com/forsale/may/hammer0502b.jpg
http://oldetoolshop.com/forsale/may/hammer0502c.jpg
L S Starrett No 275 4 Inch Toolmaker Outside Caliper. Measuring 4 3/4"
long and this weighs 1 1/4 oz unboxed. This is in reasonably good
condition and was cleaned. There ain't much in the way of patina other
than a user name marked on the spring. The spring is good. The tips
only close down to 1/16" but are good otherwise. The screw and nut are
good and travel the full distance. This ain't pristine but it will get
the job done. $24.00
http://oldetoolshop.com/forsale/may/machinisttool0502a.jpg
http://oldetoolshop.com/forsale/may/machinisttool0502b.jpg
http://oldetoolshop.com/forsale/may/machinisttool0502c.jpg
Lufkin No 142 4 Inch Toolmaker Inside Caliper. Measuring 4 3/4" long
and this weighs 1 1/4 oz unboxed. This is in reasonably good condition
and was cleaned. There is a little staining and a shop number marked on
the one leg. The spring and tips are good. The screw and nut are also
good and travel the full distance. This ain't perfect but it is a
quality tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/may/machinisttool0503a.jpg
http://oldetoolshop.com/forsale/may/machinisttool0503b.jpg
http://oldetoolshop.com/forsale/may/machinisttool0503c.jpg
Vintage 1/4 Inch Firmer Chisel. Measuring 3 1/8" from the edge to the
top of the handle, the b lade is 2 1/8" long, this is 7 3/8" overall,
and this weighs 1 3/4 oz unboxed. Not signed as to the maker, but
this looks like one of the Witherby tanged chisels with the rounded tang
bolster and the style of the handle. This is in reasonably good
condition and was cleaned. The back has a little frosting as does the
top. The handle has some dings and a few tiny bits of paint that didn't
want to come off but it's solid. This ain't the longest but for the
money it will get the job done. $14.00
http://oldetoolshop.com/forsale/may/chisel0501a.jpg
http://oldetoolshop.com/forsale/may/chisel0501b.jpg
Vintage Forged 10 oz Cross Peen Hammer. Measuring 11" overall, the head
is 4" long, the face is 1/2" in diameter, the peen is 13/16" wide, and
this weighs 10 1/2 oz unboxed. Not signed as to the maker. This has a
forged head with a steel face and peen on an iron body. This is in
decent condition and was cleaned. The last owner was something of a
"side banger" and there are lots of dings on both sides. The face has a
couple of light dings but nothing too bad. The peen is good other than
some light roughness. The handle is old and could be the original one.
That has some stains, dings, and a couple of tiny bits of paint that
didn't want to come off, but it feels solid enough. This ain't
pristine but it's an older tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/april/hammer0409a.jpg
http://oldetoolshop.com/forsale/april/hammer0409b.jpg
http://oldetoolshop.com/forsale/april/hammer0409c.jpg
Stanley Handyman No 1226 1/2 Inch Brace Screwdriver Bit. This weighs 2
oz unboxed. This is NOS (that's New Old Stock) but it wasn't stored
someplace nice. There are some dots of light patina. The tip and tang
are good other than some staining. This is a hard to find larger size.
$12.00
http://oldetoolshop.com/forsale/april/bracetool0409a.jpg
http://oldetoolshop.com/forsale/april/bracetool0409b.jpg
Forest City 1 7/8 Inch Boring Machine Auger Bit. Measuring 8 1/2" long,
the cut is 1 7/8" in diameter, the tang is 1/2" in diameter, and this
weighs 1 lb unboxed. The Forest City Bit & Tool Co was founded in 1890
in Rockford, IL and the business relocated to Hickory, NC, in 1957. The
mark is faint. This is in reasonably good condition and was cleaned.
There is a little staining overall, and a little bit of light crusty up
at the top, but nothing too bad. This doesn't have a lead screw, just a
point but that is good. The cutters and spurs are ready to work. The
tang has a few scuffs but it's good to go. This ain't minty but overall
it sure ain't bad. $35.00
http://oldetoolshop.com/forsale/april/bracetool0410a.jpg
http://oldetoolshop.com/forsale/april/bracetool0410b.jpg
Union Tool 8 oz Steel Plumb Bob. Measuring 4 1/4" long, 7/8" in
diameter, and this weighs 8 3/4 oz unboxed. This is in decent condition
and was cleaned. There are some spots of light pitting along the one
side, the rest is clean. The tip is good and the string hole is clear.
This ain't minty but it will get the job done. $14.00
http://oldetoolshop.com/forsale/april/plumbbob0405a.jpg
http://oldetoolshop.com/forsale/april/plumbbob0405b.jpg
Sculpture Associates 1/4 Inch No 20 Sweep Carving Tool. Measuring 4
9/16" from the edge to the top of the handle, the b lade is 1/4" wide
across the sweep, the sweep is a No. 11, this is 9 1/8" overall, and
this weighs 2 1/4 oz unboxed. Not signed as to the maker but it looks
like one that was sold by Sculpture Associates. This is in reasonably
good condition and was cleaned. The inside of the sweep is good. The
back has some spots and scuffs but that was never finished off real
pretty to start with. The handle has a couple of stains but it's solid
and has the original finish. This ain't got a fancy name but it will
get the job done. $15.00
http://oldetoolshop.com/forsale/april/carvingtool0402a.jpg
http://oldetoolshop.com/forsale/april/carvingtool0402b.jpg
Jordan Germany 2 Ft Spring Steel Folding Rule. This weighs 1 oz
unboxed. This is in decent condition and was cleaned. There are some
stained spots and the ink is worn on a few of the legs but all the
rulings are readable. The joints are good and hold with no play. This
ain't minty but it is a quality tool that will get the job done. $14.00
http://oldetoolshop.com/forsale/april/rule0402a.jpg
http://oldetoolshop.com/forsale/april/rule0402b.jpg
http://oldetoolshop.com/forsale/april/rule0402c.jpg
Hand Forged Loop Handle Screwdriver. Measuring 7 3/16" long, the tip is
1/4" wide, and this weighs 3 3/4 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There is a little
overall light patina. The tip was dressed at some point and that is
good to go. The handle is also good. This is another one of those
tools have not been showing up much of late. $15.00
http://oldetoolshop.com/forsale/april/hfscrewdriver0401a.jpg
http://oldetoolshop.com/forsale/april/hfscrewdriver0401b.jpg
Big Early Hand Forged Wheelwright Tapered Hook Nose Hub Reamer.
Measuring 29" overall, the reamer area is 19" long, 1 1/2" across the
tip, 3 1/2" wide at the start of the tang, and this weighs 10 lbs 10 1/4
oz unboxed. Not signed as to the maker. This is in decent condition
and was cleaned. There is lots of patina going on this guy. The back
has a void where the steel bit was forge welded to the wrought iron
body, and some others on the iron area. There are a few bits of paint
down inside some of those that didn't want to come out. There is some
light checking on the non-cutting side. The inside also has some patina
but that was never finished off real pretty to start with. The tang is
good save for some light mushrooming on the end. This ain't minty but
these tools have sure been few and far between of late. $60.00
http://oldetoolshop.com/forsale/april/hfreamer0401a.jpg
http://oldetoolshop.com/forsale/april/hfreamer0401b.jpg
http://oldetoolshop.com/forsale/april/hfreamer0401c.jpg
http://oldetoolshop.com/forsale/april/hfreamer0401d.jpg
http://oldetoolshop.com/forsale/april/hfreamer0401e.jpg
L S Starrett No 391 Machinist Center Gage. This weighs 1/4 oz unboxed.
This is in decent condition and was cleaned. There is a little frosting
and a few spots of light pitting. All the rulings are readable and the
edges and corners are good. This ain't minty but it will get the job
done. $14.00
http://oldetoolshop.com/forsale/april/machinisttool0411a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0411b.jpg
Early L S Starrett No 75 Machinist 3 Inch Outside Caliper. Measuring 3
5/16" long and this weighs 3/4 oz unboxed. Charles P. Fay of
Springfield, MA was granted Pat. No. 319,215 on June 2, 1885 for the
design of this tool. This is in decent condition and was cleaned.
There is some frosting and staining on the legs, one small spot of light
pitting, and user initials. The spring and tips are good. The nut
travels the full distance. This ain't pristine but seeing as how it's
over 115 years old, well it sure ain't bad and it will get the job
done. $16.00
http://oldetoolshop.com/forsale/april/machinisttool0412a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0412b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0412c.jpg
Keen Kutter K500 Open End Wrench. Measuring 7 1/8" long (straight
across), the ends are 5/8" and 1/2", and this weighs 3 3/4 oz unboxed.
This is in decent condition and was cleaned. There is some staining and
overall light patina. The jaws have some dings and wear. This ain't
perfect but these guys sure don't show up every day. $14.00
http://oldetoolshop.com/forsale/april/wrench0402a.jpg
http://oldetoolshop.com/forsale/april/wrench0402b.jpg
Stevens A & T Co Machinist 7 Inch Outside Caliper. Measuring 7 3/4"
long and this weighs 3 oz unboxed. The Stevens A & T Co was a Chicopee
Falls MA maker of machinist tools and was in business from 1864 until
1903 when they were purchased by Starrett. This is in reasonably good
condition for being over 110 years old and was cleaned. There is some
frosting and staining on the arms. The joint is good and holds
position. The tips are good as well. This ain't minty but it will get
the job done. $18.00
http://oldetoolshop.com/forsale/april/machinisttool0408a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0408b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0408c.jpg
Stanley No 170 5 oz Plumb Bob. This weighs 4 3/4 oz unboxed. This is
in decent condition and was cleaned. There is some wear to the finish.
The tip is good and the string hole is clear. There is a little funky
on the inside of the string cap. This ain't minty but it will get the
job done. $14.00
http://oldetoolshop.com/forsale/april/plumbbob0402a.jpg
http://oldetoolshop.com/forsale/april/plumbbob0402b.jpg
T Alteneder & Sons Drafting Architect Scaling Rule. Measuring 13 1/16"
long, 1 5/16" wide, and this weighs 1 1/2 oz unboxed. Theodore Alteneder
was a Philadephia PA inventor and maker of drafting tools who was in
business from 1850 until 1912. This is in good condition, the only
cleaning was a quick wipedown with some soap and water. There are some
light scuffs and a couple of stains but nothing too bad. All the
rulings are readable. The edges have a couple of very tiny dings. This
is a neat rule and considering that it's well over the 100 year old
mark, well it sure ain't bad. $17.00
http://oldetoolshop.com/forsale/april/draftingtool0401a.jpg
http://oldetoolshop.com/forsale/april/draftingtool0401b.jpg
http://oldetoolshop.com/forsale/april/draftingtool0401c.jpg
TWO Vintage Wood Handle Turnscrews Or Screwdrivers. The one on the left
is 5 1/2" long, the tip is 5/16" wide, the one on the right is 7 1/8"
long, the tip is 5/16" wide, and they weigh 4 1/2 oz unboxed. The one on
the right has a partial mark. These are in fair condition and were
cleaned. The b lade on the one on the left is fairly clean but
somebody wedged it in place and it sits at a bit of an angle. The one
on the right has some pitting on both sides. The left handle is rose
wood, the other one I can't say, probably beech. Both have some checks
and dings. These ain't pretty or perfect but they do have some age to
them. $17.00
http://oldetoolshop.com/forsale/april/turnscrew0401a.jpg
http://oldetoolshop.com/forsale/april/turnscrew0401b.jpg
http://oldetoolshop.com/forsale/april/turnscrew0401c.jpg
Stanley No 1222 1/2 A Carpenters Combination Square. This weighs 11 oz
unboxed. This is in reasonably good condition and was cleaned by
someone else. The head has a little wear to the finish but most of it
is there. The level vial is good but the scribe is MIA. The machined
faces have some frosting but nothing too bad. The rule has some
frosting and a few spots of light pitting. All the rulings are readable
except for one small area on the 32nds scale and the edges and corners
are good. This ain't minty but it will get the job done. $17.00
http://oldetoolshop.com/forsale/april/square0402a.jpg
http://oldetoolshop.com/forsale/april/square0402b.jpg
http://oldetoolshop.com/forsale/april/square0402c.jpg
http://oldetoolshop.com/forsale/april/square0402d.jpg
http://oldetoolshop.com/forsale/april/square0402e.jpg
Hand Forged Farrier Blacksmith Fuller Head. Measuring 3 3/8" long. the
face is slightly curved and 1" high, and this weighs 9 3/4 oz unboxed.
Not signed as to the maker. This is in decent condition and was
cleaned. There is some overall light pitting and patina. The face is
good other than a couple of tiny dings. The striking end does have a
little mushrooming. The punched eye has a little crusty inside but it's
good with no cracks that I can see. This ain't pretty or perfect, but
then neither are you and this will get the job done. $18.00
http://oldetoolshop.com/forsale/april/blacksmith0401a.jpg
http://oldetoolshop.com/forsale/april/blacksmith0401b.jpg
http://oldetoolshop.com/forsale/april/blacksmith0401c.jpg
Vintage Wood Handle Box Scraper. Measuring 13 1/8" overall, the b lade
is 5 9/16" long (straight across the edge) and this weighs 15 1/4 oz
unboxed. Not signed as to the maker. This is in decent condition and
was cleaned. Somebody had painted the head with flat black paint. I got
rid of most of that on the outside but there still is some on the inside
of the b lade. The outside is clean up by the edge and after that here
is some light pitting. The inside has some overall light pitting. The
brass ferrule has a couple of checks. The handle also has a check under
the ferrule but the head is pinned in place. The handle has some dings,
stains, and wear but it's solid. This ain't pretty but then it wasn't
made to do a pretty job. $25.00
http://oldetoolshop.com/forsale/mar/scraper0301a.jpg
http://oldetoolshop.com/forsale/mar/scraper0301b.jpg
http://oldetoolshop.com/forsale/mar/scraper0301c.jpg
http://oldetoolshop.com/forsale/mar/scraper0301d.jpg
Unusual Early Hand Forged Cross Peen Hammer. Measuring 9 3/8" overall,
the head is 4 7/8" long, the face is 7/8" wide, 11/16" widee, the peen
is 15/16" wide (straight across), and this weighs 15 3/4 oz unboxed.
Not signed as to the maker. This is in decent condition and was
cleaned. There is some overall pitting on the head. The face and peen
have some light pitting. The eye looks good with no cracks. The handle
has some some dings, stains, wear, and there is a check under the eye
from the wedge. This ain't minty for sure but it is a neat older hammer
to say the least.
http://oldetoolshop.com/forsale/mar/earlyhammer0301a.jpg
http://oldetoolshop.com/forsale/mar/earlyhammer0301b.jpg
http://oldetoolshop.com/forsale/mar/earlyhammer0301c.jpg
Kraeuter No 1850-6 Wire Nipper Pliers. Measuring 6 1/8" long, the jaws
are 1 1/16" wide, 5/16" deep, and this weighs 7 3/4 oz unboxed. This is
in reasonably good condition and was cleaned. There ain't much patina
other than some staining. The area under the jaws was never finished
off real pretty like to start with. The jaws have a couple of very tiny
dings but nothing too bad and they close up tight and flush. The joint
is good. This is a quality tool that will get the job done. %16.00
http://oldetoolshop.com/forsale/mar/pliers0302a.jpg
http://oldetoolshop.com/forsale/mar/pliers0302b.jpg
Tools of All Trades
Goodell-Pratt No 1218 Inside Micrometer Set. This weighs lbs 15 1/2
oz unboxed. This is in reasonably good condition and was not cleaned.
There is a little bit of light patina on the head but nothing too bad.
The head works smoothly. The rods are also all good and all are
present. The case has some light wear but the hinges and catches are
good. This ain't perfect but it is a quality set that will get the job
done. $60.00
http://oldetoolshop.com/forsale/mar/machinisttool0317a.jpg
http://oldetoolshop.com/forsale/mar/machinisttool0317b.jpg
Vintage Craftsman Machinist Center Gage. This weighs 1/4 oz unboxed.
This is in reasonably good condition and was not cleaned. There are some
light scuffs and a shop number marked on the one side. All the rulings
are readable and the edges and corners are crisp. This ain't minty but
it will get the job done. $14.00
http://oldetoolshop.com/forsale/mar/machinisttool0315a.jpg
http://oldetoolshop.com/forsale/mar/machinisttool0315b.jpg
Wolverine Brass Works Pat 1911 Universal Seating Tool. Measuring 5 1/8"
long and this weighs 10 3/4 oz unboxed. The body has a patent date of
Oct 11, 1911, the cutting heads have a patent date of April 25, 1911,
but finding the actual patents have been elusive. This is in decent
condition and was cleaned. There is some overall wear and light
patina. There are two cutting heads and they unscrew. The cutting
heads have a little wear but could be used. The brass guides can be
reversed to fit a variety of applications. This ain't minty but then
working tools that, at the least, 90 years old, rarely are. $20.00
http://oldetoolshop.com/forsale/mar/plumbertool0301a.jpg
http://oldetoolshop.com/forsale/mar/plumbertool0301b.jpg
http://oldetoolshop.com/forsale/mar/plumbertool0301c.jpg
Bridgeport Matchless 12 Inch Screwdriver. Measuring 12" long, the tip
is 5/16" wide, and this weighs 6 1/4 oz unboxed. This is in good
condition and was not cleaned. There ain't much in the way of patina to
fuss about. The tip and shaft are good. The handle finish is original
and save for some tiny dings, is near perfect. The end button also has a
few light dings. This is a good looking and top quality tool to say the
least. $20.00
http://oldetoolshop.com/forsale/mar/screwdriver0304a.jpg
http://oldetoolshop.com/forsale/mar/screwdriver0304b.jpg
Vintage Danielson 6 Inch Needlenose Pliers. Measuring 6 5/16" long, the
jaws are 1 7/16" deep, a little under 1/8" wide at the tips, and this
weighs 4 oz unboxed. This is in decent condition and was cleaned.
There is some wear to the plating. The jaws have some tiny dings on the
teeth but are good for the most part and they close flush. The joint
has a wee bit of play. This ain't minty but it will get the job done.
$14.00
http://oldetoolshop.com/forsale/mar/pliers0301a.jpg
http://oldetoolshop.com/forsale/mar/pliers0301b.jpg
Vintage 4 1/2 oz Plated Plumb Bob. Measuring 3 7/8" long, 1 3/16" in
diameter, and this weighs 4 1/2 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There are some
dings and wear but most of the plating is present. The tip is good and
the string hole is clear. This ain't the fanciest but it is a neat
older tool. $14.00
http://oldetoolshop.com/forsale/mar/plumbbob0301a.jpg
http://oldetoolshop.com/forsale/mar/plumbbob0301b.jpg
Old 2 3/4 Lb Ball Peen Hammer Head. Measuring 5 1/4" long, the face is
1 1/2" in diameter, the peen is 1 3/8" in diameter, and this weighs 2
lbs 13 oz unboxed. There are user names and initials but no maker's
mark that I can see. This is in decent condition and was cleaned.
There is some overall light patina. The face is good other than a
little wear around the edge. The peen has some light pitting and a deep
scratch on the one side. The eye has a little dinging on top but it's
solid. This ain't pristine but it's an older tool that will get the job
done. $17.00
http://oldetoolshop.com/forsale/mar/hammer0301a.jpg
http://oldetoolshop.com/forsale/mar/hammer0301b.jpg
http://oldetoolshop.com/forsale/mar/hammer0301c.jpg
Stanley No 88 Clapboard Sliding Marker Gauge. This weighs 11 oz
unboxed. James F. Beebe of New Haven, CT was granted Pat. No. 344,937
on July 6, 1886 for the design of this tool. This is in decent
condition and was cleaned. The body has some frosting and spots of
light pitting. The b lade is good and still has most of the original
bluing. The screws work. The handle has some wear, dings, and stains,
but it's solid. This ain't minty but it ain't like clapboard hanging is
an indoor sport. Just saying. $20.00
http://oldetoolshop.com/forsale/mar/stanley880301a.jpg
http://oldetoolshop.com/forsale/mar/stanley880301b.jpg
---------------------------------------------
"A man who has never gone to school may steal from a freight car; but if
he has a university education, he may steal the whole railroad."
Theodore Roosevelt
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
|
