Howdy. This winter sure showed up with a vengeance this month. Flea
runs have been 25% of what they usually are during the winter months,
but the few that I've been on have been productive and the shop piles
keep producing so there are a lot of good fresh items this time around.
PayPal is preferred (if you use it) on all items. It's easier for me to
ship items off of a paid PayPal invoice, especially First Class ones.
Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
---------------------------------------------------
Stanley SW 1/4 Inch Everlasting Chisel. Measuring 3 11/16" from the
edge to the start of the ferrule, the blade is 2 13/16" long, this is 7
3/4" overall, and this weighs 5 1/2 oz unboxed. This is in decent
condition and was cleaned. The back has a few dots of pitting and some
scuff marks. Somebody got kinda creative the last time that this was
sharpened and the edge is rounded. The top is scuffed down a bit and
there is some staining on the sides. The ferrule has some overall
frosting and some pitting down by the handle, but it's solid with no
cracks. The handle has some stains, but it's solid and the striking
button is just about pristine, which you don't see too often with these
guys. This ain't minty, but it will get the job done. $23.00
http://oldetoolshop.com/forsale/jan/chisel0104a.jpg
http://oldetoolshop.com/forsale/jan/chisel0104b.jpg
http://oldetoolshop.com/forsale/jan/chisel0104c.jpg
Lakeside 8 Inch Wing Compass Or Divider. Measuring 8 1/4" long and this
weighs 5 1/4 oz unboxed. This is in decent condition and was cleaned.
There is some overall light frosting and pitting. The joint and tips
are good. The locking screw and the fine adjustment nut both work.
This ain't minty, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/jan/divider0104a.jpg
http://oldetoolshop.com/forsale/jan/divider0104b.jpg
http://oldetoolshop.com/forsale/jan/divider0104c.jpg
Early Hand Forged Bark Barking Spud. Measuring 25 3/8" overall, the
iron area is 8 3/8" long, the head is 2 7/8" wide, and this weighs 2 lbs
4 1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall light pitting on the
iron. The edge has some light dings, but is fairly good. The forge
weld line for the socket is visible, but it's solid. The handle is home
grown. That has some long and deep checks, and some long gone worm
holes, but it's solid enough to use, as long as you don't hit it with a
sledge hammer. The handle is loose in the socket, but it is pinned in
there. Pretty and perfect moved out of town on this guy a while back,
but these guys sure ain't getting any easier to come by, at least around
these here parts. $40.00
http://oldetoolshop.com/forsale/jan/hfbarkspud0101a.jpg
http://oldetoolshop.com/forsale/jan/hfbarkspud0101b.jpg
http://oldetoolshop.com/forsale/jan/hfbarkspud0101c.jpg
H Disston & Sons No 4 12 Inch Back Saw or Backsaw. Measuring 16 7/8"
overall, the blade is 12 1/16" long, 2 15/16" high (from the edge to the
start of the back), this is sharpened to 14 PT (13 TPI) CC, and this
weighs 1 lb 7 3/4 oz unboxed. Based on the medallion, this was made by
Disston between 1947 and 1953. This is in reasonably good condition and
was cleaned. The front of the blade is good save for some frosting.
The etch is faint, but readable. The back of the blade has some spots of
light pitting and also some on the steel back. All the teeth are
present and the edge is straight, but this will need a sharpening. The
tote has some dings, stains, and a few tiny bits of paint, but it
retains most of the original finish plus a coat of wax. The nuts are
brass plated steel, but the plating was pretty much gone. This ain't
pristine, but it is a solid tool that will get the job done. $48.00
http://oldetoolshop.com/forsale/jan/saw0104a.jpg
http://oldetoolshop.com/forsale/jan/saw0104b.jpg
http://oldetoolshop.com/forsale/jan/saw0104c.jpg
http://oldetoolshop.com/forsale/jan/saw0104d.jpg
http://oldetoolshop.com/forsale/jan/saw0104e.jpg
Stanley No 60 1/2 Adjustable Throat Low Angle Block Plane. This weighs
1 lb 3 oz unboxed. This is in decent condition, it was cleaned and
refinished. The sides have some frosting, light scratches, and tiny
dings. The sole has some deeper scratches, frosting, and some more
dings. The mouth is good with no cracks, and the mouth adjuster works.
The lever is a replacement. The japanning was a mess on both the body
and the cap, so that's why it was repainted. The cap is good. The
blade has some light patina on the exposed areas. The cutting face has
some scuffs and a couple of dots, but nothing too bad. The blade will
need a sharpening. All the screws work and were oiled. This ain't
minty fresh, but it will get the job done. $42.00
http://oldetoolshop.com/forsale/jan/stanley060120102a.jpg
http://oldetoolshop.com/forsale/jan/stanley060120102b.jpg
http://oldetoolshop.com/forsale/jan/stanley060120102c.jpg
http://oldetoolshop.com/forsale/jan/stanley060120102d.jpg
Small Planishing Hammer For Light Metal Work. Measuring 8" overall, the
head is 4" long, the faces are 1/2" high, 5/8" wide, and this weighs 7
oz unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. The head has some light patina and scuffs
left over from when it was made. Both faces are very slightly convex.
The one face is good, the other one has a ding on the one side and some
very light pitting. The eye is good. The handle was somebody else's
idea of a good time, but it will get the job done. This ain't minty,
but it will get the job done. $22.00
http://oldetoolshop.com/forsale/jan/hammer0112a.jpg
http://oldetoolshop.com/forsale/jan/hammer0112b.jpg
http://oldetoolshop.com/forsale/jan/hammer0112c.jpg
Goodell-Pratt No 1218 Inside Micrometer Set. This weighs 15 1/2 oz
unboxed. This is in reasonably good condition and was not cleaned.
There is a little bit of light patina on the head but nothing too bad.
The head works smoothly. The rods are also all good and all are
present. The case has some light wear but the hinges and catches are
good. This ain't perfect but it is a quality set that will get the job
done. $60.00
http://oldetoolshop.com/forsale/jan/machinisttool0115a.jpg
http://oldetoolshop.com/forsale/jan/machinisttool0115b.jpg
Vintage User Crafted Ball Peen Hammer. Measuring 11 3/4" overall, the
head is 2 7/8" long, the face and peen are 13/16" in diameter, and this
weighs 10 1/4 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. The head has some light patina, but nothing
too bad. The face has some dings and I did clean some mushrooming off
of the edge. The peen also has some dings. The handle has some stains
and is slightly warped looking from the side, but it's solid. This
ain't minty, but will get the job done. $14.00
http://oldetoolshop.com/forsale/jan/hammer0110a.jpg
http://oldetoolshop.com/forsale/jan/hammer0110b.jpg
http://oldetoolshop.com/forsale/jan/hammer0110c.jpg
http://oldetoolshop.com/forsale/jan/hammer0110d.jpg
Giller No 305 4 Inch Slip Joint Ignition Pliers. Measuring 4 7/16" long
and this weighs 1 1/4 oz unboxed. This is in good condition and was not
cleaned. I really don't think that it was used much, if at all. There
is a wee bit of funky on the one side of the head. The jaws are good and
the slip joint works just dandy. This is a neat little tool and they
sure don't get much better than this. $15.00
http://oldetoolshop.com/forsale/jan/pliers0102a.JPG
http://oldetoolshop.com/forsale/jan/pliers0102b.JPG
http://oldetoolshop.com/forsale/jan/pliers0102c.JPG
Early Disston Fancy Screw 8 Inch Adjustable Bevel Square. This weighs 4
oz unboxed. Not signed as to the maker, but few of these were. This is
in decent condition and was cleaned. The blade has a few spots of light
pitting and rust etching, but nothing too bad overall and it still has
some of the original finish. The edges are good, but the lower corner
is worn a little. The handle has some dings, stains, and a user initial
marked on the back. The fancy head screw works. This ain't perfect,
but it will get the job done. $18.00
http://oldetoolshop.com/forsale/jan/square0104a.jpg
http://oldetoolshop.com/forsale/jan/square0104b.jpg
http://oldetoolshop.com/forsale/jan/square0104c.jpg
http://oldetoolshop.com/forsale/jan/square0104d.jpg
Sculpture Associates 1/4 Inch No 11 Sweep Carving Tool Gouge. Measuring
4 9/16" from the edge to the top of the handle, the b lade is 1/4" wide
across the sweep, the sweep is a No. 11, this is 9 1/8" overall, and
this weighs 2 1/4 oz unboxed. Not signed as to the maker but it looks
like one that was sold by Sculpture Associates. This is in reasonably
good condition and was cleaned. The inside of the sweep is good. The
back has some spots and scuffs but that was never finished off real
pretty to start with. The handle has a couple of stains but it's solid
and has the original finish. This ain't got a fancy name but it will get
the job done. $15.00
http://oldetoolshop.com/forsale/jan/carvingtool0101a.jpg
http://oldetoolshop.com/forsale/jan/carvingtool0101b.jpg
H Reid Patent 1882 No 1 Lightning Brace Screwdriver. Measuring 18 1/4"
long and this weighs 1 lb 6 1/2 oz unboxed. Alban H. Reid of
Philadelphia, PA was granted Pat. No. 268,938 on Dec. 12, 1882 for the
design of this tool. This is in reasonably good condition and was
cleaned. There is some wear to the plating on the shaft, but it's about
50% present overall. The lower grip has some funky and a chip off of
the one side, but it's solid. The Booth screwdriver bit is original to
the tool. That has some scuffs, but the tip is good and the screw
works. The shaft extends completely and smoothly. The Lignum Vitae pad
has a few tiny dots of paint on the top that didn't want to come off and
some light funky on the underside, but both are solid with no cracks.
This ain't minty, but these guys rarely are and this one is better than
most of these that I have been seeing lately. $25.00
http://oldetoolshop.com/forsale/jan/pushscrewdriver0101a.jpg
http://oldetoolshop.com/forsale/jan/pushscrewdriver0101b.jpg
http://oldetoolshop.com/forsale/jan/pushscrewdriver0101c.jpg
Miller Falls No 98 8 Inch Adjustable Bevel Square. This weighs 3 oz
unboxed. This is in reasonably good condition and was lightly cleaned.
The blade has some small dots of patina and one dot of paint, but it has
almost all of the bluing. The edges and corners are good. The handle
also has a few dots of paint, some small spots where the finish is worn,
and some light dings on the sides, but overall nothing too bad. The
locking screw is good. This ain't pristine, but these guys sure don't
show up very often and this one will get the job done. $22.00
http://oldetoolshop.com/forsale/jan/square0103a.jpg
http://oldetoolshop.com/forsale/jan/square0103b.jpg
http://oldetoolshop.com/forsale/jan/square0103c.jpg
http://oldetoolshop.com/forsale/jan/square0103d.jpg
Douglass Mfg 5/8 Inch Socket Firmer Chisel. Measuring 8 3/16" from the
edge to the end of the socket, the blade is 5 5/16" long, this is 12
3/4" overall, and this weighs 6 3/4 oz unboxed. James Swan was in
charge of Douglass for a number of years prior to purchasing the company
and putting his name on the door. This is in decent condition and was
cleaned. The back has some frosting and a few spots of very light
pitting, but nothing too bad. The top also has some patina. The socket
is good, I did take a wee bit of mushrooming off of the end. The handle
is a replacement. That has some stains and dings, but it's solid. This
ain't minty, but it is a quality tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/jan/chisel0101a.jpg
http://oldetoolshop.com/forsale/jan/chisel0101b.jpg
http://oldetoolshop.com/forsale/jan/chisel0101c.jpg
TWO Union 3 Inch Machinist Spring Calipers. There is a No. 12 inside
caliper measuring 3 11/16", a No. 14 outside caliper measuring 3 15/16"
long, and they weigh 1 1/2 oz unboxed. These are in reasonably good
condition and were cleaned. There is some frosting and staining on the
legs, but nothing too bad. The springs are quite stiff and the tips are
good. Both nuts travel the full distance smoothly. These ain't minty,
but they are quality tools that will get the job done. $18.00
http://oldetoolshop.com/forsale/jan/machinisttool0108a.jpg
http://oldetoolshop.com/forsale/jan/machinisttool0108b.jpg
http://oldetoolshop.com/forsale/jan/machinisttool0108c.jpg
L S Starrett No 74 Fay Pattern 4 Inch Inside Caliper. Measuring 4
13/16" long and this weighs 1 1/2 oz unboxed. This is in reasonably
good condition and was lightly cleaned. There ain't much in the way of
patina, other than some light scuffs, a few stains, and a user name
lightly marked on the one leg. The joint and tips are good and the nut
travels the full distance smoothly. NOTE: This does not have the quick
set nut, but not all of these did. This ain't pristine, but it will get
the job done. $15.00
http://oldetoolshop.com/forsale/jan/machinisttool0105a.jpg
http://oldetoolshop.com/forsale/jan/machinisttool0105b.jpg
http://oldetoolshop.com/forsale/jan/machinisttool0105c.jpg
Stanley No 177 Radio Screwdriver. Measuring 5 1/2" long, the tip is
1/8" wide, and this weighs 1 oz unboxed. This is in reasonably good
condition, it was cleaned and the handle refinished. The tip has a
little wear and was dressed at some point. There is some light patina
on the shaft. The original finish on the handle was pretty much gone,
so that's why it was redone. That ain't perfect, but it's better than
it was. This ain't minty, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/jan/screwdriver0101a.jpg
http://oldetoolshop.com/forsale/jan/screwdriver0101b.jpg
Big Hand Forged Turnscrew Screwdriver Brace Bit. Measuring 6 5/16"
long, 7/8" wide across the tip, and this weighs 9 3/4 oz unboxed. Not
signed as to the maker. This is in reasonably good condition and was
cleaned. There is a little overall patina, but nothing too bad. The
tip has a wee bit of roughness. The tang is good. This is a neat tool
and one that does not show up very often in this kind of shape. $14.00
http://oldetoolshop.com/forsale/jan/hfbracetool0101a.jpg
http://oldetoolshop.com/forsale/jan/hfbracetool0101a.jpg
Early Hand Forged Scraper. Measuring 11 1/2" long, 2 1/4" wide across
the end of the head, and this weighs 10 oz unboxed. Not signed as to
the maker. This is in decent condition and was cleaned. There is some
pitting on both sides of the head and a little mushrooming on the
sides. The edge is fairly good and was dressed recently. The handle
and eye are also good. This ain't pristine and it ain't no kitchen
flipper either, but these guys sure have not been showing up much of
late. $20.00
http://oldetoolshop.com/forsale/jan/hfscraper0101a.jpg
http://oldetoolshop.com/forsale/jan/hfscraper0101b.jpg
http://oldetoolshop.com/forsale/jan/hfscraper0101c.jpg
Stanley No SB4 Smooth Or Smoothing Plane. This weighs 2 lbs 9 1/4 oz
unboxed. Made in Merry Olde England. This is in good condition and was
lightly cleaned. The sides still have the factory finish which has a
few light scratches. I did remove the finish from the sole along with a
bunch of white paint and that is good to go. The finish is original and
is perfect other than a couple of tiny dings. The cap is good. The
blade also had the finish removed from the front and is clean on the
working area. The plastic tote and knob are good other than a few very
light dings. All the screws work. This ain't the best plane that
Stanley ever made, but it will get the job done. $23.00
http://oldetoolshop.com/forsale/jan/stanleysb40101a.jpg
http://oldetoolshop.com/forsale/jan/stanleysb40101b.jpg
http://oldetoolshop.com/forsale/jan/stanleysb40101c.jpg
http://oldetoolshop.com/forsale/jan/stanleysb40101d.jpg
Vintage 9 oz Riveting Hammer Head. Measuring 4" long, the face is
11/16" in diameter, the peen is 7/8" wide, and this weighs 9 oz
unboxed. This is signed, but it's too faint to read. This is in decent
condition and was cleaned. There ain't too much patina overall other
than some dings and user pin punched initials on the sides. The face
has some light pitting and dings, but nothing too bad. The same for the
peen. The eye is good to go. This ain't pristine, but it will get the
job done. $15.00
http://oldetoolshop.com/forsale/dec/hammer1212a.jpg
http://oldetoolshop.com/forsale/dec/hammer1212b.jpg
http://oldetoolshop.com/forsale/dec/hammer1212c.jpg
Horn & Ellis Philadelphia Cobblers Pivot Head Boot Peg Float. Measuring
20 7/8" overall, the head is 2 7/8" long, 1 1/8" wide at the center, and
this weighs 13 oz unboxed. Horn & Ellis were Philadelphia PA makers of
leather and cobblers tools, they are listed as working from 1870 until
1871, but probably worked longer. This is in decent condition and was
cleaned. There is some pitting on the head. The teeth also have some
spots of light pitting, but the edges feel okay. They will need a quick
touch-up though. The head pivot works. The shaft has some deeper spots
of pitting. The handle is original to the tool. That has some thin
checks under the ferrule and the usual stains and dings, but it's solid
enough and on tight. Pretty and perfect moved out of town on this guy a
while back, but these guys sure do not show up very often any more. $26.00
http://oldetoolshop.com/forsale/dec/leathertool1205a.jpg
http://oldetoolshop.com/forsale/dec/leathertool1205b.jpg
http://oldetoolshop.com/forsale/dec/leathertool1205c.jpg
Magic Scale Co Chicago Stitch Marking Wheel. Measuring 6" long, this
marks 10 stitches per inch, and this weighs 1 1/2 oz unboxed. This is in
reasonably good condition and was cleaned. There is a little frosting
on the head. This has the original price stamped on the back. The
wheel spins freely and leaves clean marks. The handle has some stains,
but it's solid. This is a neat tool that will get the job done. $16.00
http://oldetoolshop.com/forsale/dec/leathertool1206a.jpg
http://oldetoolshop.com/forsale/dec/leathertool1206b.jpg
http://oldetoolshop.com/forsale/dec/leathertool1206c.jpg
Stoddart Bell Electotype 12 Inch Typesetters Rule. Measuring 13 9/16"
overall and this weighs 1 1/2 oz unboxed. Also called a Pica Pole.
This is in good condition and was not cleaned. There are some light
scuffs, but nothing too bad. All the rulings are readable and the edges
are good. This is a neat rule for any collection. $14.00
http://oldetoolshop.com/forsale/dec/rule1204a.jpg
http://oldetoolshop.com/forsale/dec/rule1204b.jpg
http://oldetoolshop.com/forsale/dec/rule1204c.jpg
L S Starrett No 26 4 Inch Firm Joint Outside Caliper. Measuring 4 5/16"
long and this weighs 1 1/4 oz unboxed. This is in decent condition and
was cleaned. There are some scratches on the one leg, user initials on
both sides, and some overall light pitting. The joint is good and holds
position. The tips are also good save for the patina. This ain't
pristine, but it is a quality tool that will get the job done. $14.00
http://oldetoolshop.com/forsale/dec/machinisttool1207a.jpg
http://oldetoolshop.com/forsale/dec/machinisttool1207b.jpg
http://oldetoolshop.com/forsale/dec/machinisttool1207c.jpg
Vintage Small Bench Vise. The body is 4 3/4" high, the jaws are 2 3/16"
wide, this will fit a benchtop up to 1 9/16" thick, and this weighs 1 lb
13 3/4 oz unboxed. Not signed as to the maker. This is in reasonably
good condition and was cleaned. The jaws have some scuffs and wear on
the tops and there is a small gap (1/32") at the top when they are
closed. The body has some wear to the finish, but most of it is
present. Both screws work and travel the full distance. This ain't
minty, but it will get the job done. $20.00
http://oldetoolshop.com/forsale/dec/vise1201a.jpg
http://oldetoolshop.com/forsale/dec/vise1201b.jpg
http://oldetoolshop.com/forsale/dec/vise1201c.jpg
http://oldetoolshop.com/forsale/dec/vise1201d.jpg
Essex Knife Co Cigar Makers Tobacco Trimming Knife. Measuring 7 1/16"
overall, the blade is 3 5/16" long, 1 5/16" wide, and this weighs 1 oz
unboxed. This is in reasonably good condition and was cleaned by
someone else. There is some light pitting and staining at the front end
of the blade on both sides and a few dots farther back, but it's clean
for the most part. The edge is good. The handle has some light stains,
but has almost all of the original finish. There is a hole in the end
where somebody had put an eye hook at some point. This ain't minty, but
this sure ain't a common maker for this tool either. $19.00
http://oldetoolshop.com/forsale/dec/knife1201a.jpg
http://oldetoolshop.com/forsale/dec/knife1201b.jpg
http://oldetoolshop.com/forsale/dec/knife1201c.jpg
Vintage Forged 1 1/2 lb Ball Peen Hammer Head. Measuring 4 1/2" long,
the face is 1 1/2" in diameter, the peen is 1 1/4" in diameter, and this
weighs 1 lb 7 3/4 oz unboxed. Not signed as to the maker, but this is a
forged head. There is some overall light patina, including some scuff
marks on both sides of the eye, that are either from a previous cleaning
or left over from when this was made. The face has some light dings and
there is a visible forge weld line around the side where the steel meets
the body, but it's not cracked. The peen also has a few dings. The eye
is good save for a couple of light dings on the inside. This ain't
pristine, but it's an old dawg that will get the job done. $17.00
http://oldetoolshop.com/forsale/dec/hammer1207a.jpg
http://oldetoolshop.com/forsale/dec/hammer1207b.jpg
http://oldetoolshop.com/forsale/dec/hammer1207c.jpg
http://oldetoolshop.com/forsale/dec/hammer1207d.jpg
Big Early Hand Forged Shipbuilders Gouge. Measuring 23 1116" overall,
the head is 3 3/4" long (down the center), 2 1/8" wide across the
outside of the sweep, and this weighs 3 lbs 6 1/2 oz unboxed. Not
signed as to the maker. This is in decent condition and was cleaned.
The back of the head has some light pitting and patina. The edge is
chipped on both sides, the one being deeper. The inside of the head was
never finished off real pretty like to start with. The handle has some
light patina and there is a noticeable bend looking from the side. I
put it in the vise and gave it a couple of pulls, but it's going to take
some heat to get it straight. The striking has some dings, but nothing
too bad. This ain't minty, but it ain't like these guys show up every
day. $28.00
http://oldetoolshop.com/forsale/dec/hfgouge1202a.jpg
http://oldetoolshop.com/forsale/dec/hfgouge1202b.jpg
http://oldetoolshop.com/forsale/dec/hfgouge1202c.jpg
http://oldetoolshop.com/forsale/dec/hfgouge1202d.jpg
TWO AETCO Tools. On the left is a 5/16" skew chisel measuring 4 9/16"
from the edge to the top of the handle, the blade is 3 7/8" long, this
is 9 3/4" overall, on the right is a 1/4" gouge measuring 6 5/16" from
the edge to the top of the handle, the blade is 4 13/16" long, 1/4" wide
across the inside of the sweep, 5/16" across the outside, this is 10
15/16" overall, and they weigh 5 oz unboxed. The American Edge Tool
Company worked in or around the Philadelphia PA area, from the late
1940's until the early 1960's. These are NOS (that's New Old Stock), but
they weren't stored some place nice and I did some light cleaning on
them. The chisel has a little staining, but nothing serious patina
wise. The gouge is clean on both sides of the sweep. The handle on the
chisel is good. The handle on the gouge has a thin check under the
ferrule and another one down along the side. These ain't perfect, but
they will get the job done. $25.00
http://oldetoolshop.com/forsale/dec/chisel1204a.jpg
http://oldetoolshop.com/forsale/dec/chisel1204b.jpg
http://oldetoolshop.com/forsale/dec/chisel1204c.jpg
http://oldetoolshop.com/forsale/dec/chisel1204d.jpg
Early 12 Inch Adjustable Bevel Square. The blade is 11 15/16" long, the
handle is 6 3/4" high, and this weighs 5 1/2 oz unboxed. Not signed as
to the maker, from the style of the handle (2 pieces of wood with a
brass insert at the end), my guess is that this is mid 1800's English or
American. This is in decent condition and was cleaned. There are some
light spots of pitting on the flat area of the blade and some more along
the slot. The edges and corners are good. The rosewood handle has some
wear on the edges and some light dings, but it's solid. The locking
screw works. This ain't pristine, but it's a well made tool that will
get the job done. $18.00
http://oldetoolshop.com/forsale/dec/square1203a.jpg
http://oldetoolshop.com/forsale/dec/square1203b.jpg
http://oldetoolshop.com/forsale/dec/square1203c.jpg
http://oldetoolshop.com/forsale/dec/square1203d.jpg
Wooden Spar Or Mast Shave Plane. Measuring 10" long, the iron is 1
5/16" wide across the edge, this is 1 7/8" wide across the top, 2 1/4"
high, and this weighs 1 lb 4 1/4 oz unboxed. Not signed as to the
maker, other than some initials marked on the top. This is in decent
condition and was cleaned. I'm not sure what kind of wood this is, it's
light colored inside the mouth, but it doesn't look like beech. There
are some dings, stains, and punch marks on the body. The sole has some
scratches and wear. The mouth looks like it was opened a little and
there is a little chipping on the sides. The wedge has a grain check
along the one side, but it holds. The Newbould iron does have some
pitting on the face and there is a little chipping on the edge. I did
run a file over some sharp mushrooming on the back of the top. This
ain't minty, but then working tools rarely are. $22.00
http://oldetoolshop.com/forsale/dec/woodenplane1201a.jpg
http://oldetoolshop.com/forsale/dec/woodenplane1201b.jpg
http://oldetoolshop.com/forsale/dec/woodenplane1201c.jpg
http://oldetoolshop.com/forsale/dec/woodenplane1201d.jpg
http://oldetoolshop.com/forsale/dec/woodenplane1201e.jpg
Stanley Rule & Level No 25 Type 4 8 Inch Adjustable Bevel Square. This
weighs 3 1/2 oz unboxed. Edmund A. Schade of New Britain, CT was
granted Pat. No. 769,325 on Sept. 6, 1904 for the design of this tool
which was made by Stanley from 1904 to 1909. This is in decent condition
and was cleaned. The blade has some spots of pitting and frosting. The
edges and corner are good. The handle has some dings and wear, but it's
solid. The locking screw does it's job. This ain't minty, but then not
too many tools of this are. $19.00
http://oldetoolshop.com/forsale/dec/square1202a.jpg
http://oldetoolshop.com/forsale/dec/square1202b.jpg
http://oldetoolshop.com/forsale/dec/square1202c.jpg
http://oldetoolshop.com/forsale/dec/square1202d.jpg
Wood Cased Sharpening Stone. The stone is 6" long, 1 15/16" wide, 3/4"
thick at the one end, 7/8" at the other end, the case is 7 7/8" long, 2
11/16" wide, 1 1/2" high, and this weighs 1 lb 3/4 oz unboxed. Not
signed as to the maker. The stone is a man made double sided one and
the case is pine. This is in decent condition and was cleaned. The
stone has some wear looking from the side on the medium face, but is
fairly straight looking from the ends. The fine side has a very slight
dip (like 1/32" or so) in the center, but is reasonably good. The case
was made from two blocks of pine. That has some stains on the outside
and some slurry residue on the inside, but it's solid. This ain't
minty, but it will get the job done. $20.00
http://oldetoolshop.com/forsale/dec/sharpeningstone1202a.jpg
http://oldetoolshop.com/forsale/dec/sharpeningstone1202b.jpg
http://oldetoolshop.com/forsale/dec/sharpeningstone1202c.jpg
http://oldetoolshop.com/forsale/dec/sharpeningstone1202d.jpg
http://oldetoolshop.com/forsale/dec/sharpeningstone1202e.jpg
Vintage 7 oz Ball Peen Hammer. Measuring 10 1/4" overall, the head is
3" long, the face is 5/8" in diameter, the peen is 5/8" in diameter, and
this weighs 7 oz total unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is a little frosting and patina
on the head, including some dings on the sides of the eye. The peen is
fairly good save for a little flattening of the tip. The face has some
light dings and a wee bit of mushrooming around the edge. The handle is
old and is probably the original one. That has some dings under the
eye, some overall staining, and a little chipping at the end, but it's
solid enough to use as long as you don't try to pound framing nails with
this guy. This ain't minty, but it's a neat older hammer that will get
the job done. $16.00
http://oldetoolshop.com/forsale/dec/hammer1203a.jpg
http://oldetoolshop.com/forsale/dec/hammer1203b.jpg
http://oldetoolshop.com/forsale/dec/hammer1203c.jpg
Hand Forged 11 oz Cross Peen Hammer Head. Measuring 4 11/16" long, the
face is 11/16" in diameter, the peen is 1 3/4" wide, and this weighs 11
1/4 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall patina including some
pitting, and some dings and cut marks on the sides. The face has some
light pitting and a couple of small chips on the sides. The punched eye
is good other than than being extended for some reason at the back on
the underside. This ain't pretty or perfect, but it's an older tool
that will get the job done. $16.00
http://oldetoolshop.com/forsale/dec/hammer1205a.jpg
http://oldetoolshop.com/forsale/dec/hammer1205b.jpg
http://oldetoolshop.com/forsale/dec/hammer1205c.jpg
V & M Engineering Veeco Drafting Compass & Box. The tool is 3 7/8" long
(from the tips to the top of the spring) and this all weighs 1 1/2 oz
unboxed. The tool is in very good condition and was not cleaned. There
is nothing at all patina wise to fuss about. The tips are good and all
the screws work. The box has some stains and wear, but it's solid.
This is a quality tool that is ready to work. $14.00
http://oldetoolshop.com/forsale/dec/draftingtool1203a.jpg
http://oldetoolshop.com/forsale/dec/draftingtool1203b.jpg
http://oldetoolshop.com/forsale/dec/draftingtool1203c.jpg
Early Hand Forged Pointed Peen Strap Hammer Head. Measuring 5 3/16"
long, the face is 11/16" high, 7/8" wide, the peen is 5/16" wide, and
this weighs 11 1/2 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some overall light patina
including some dings on the sides. The face has some dings, wear, and
there is a ring of mushrooming around the edge. I did run a file over
some sharp spots, but there are few tiny checks in there. The peen is
good. The punched eye is good and the fact that it's notched and
beveled at the front is what makes me believe that this was originally a
strap hammer. This ain't perfect, but it sure ain't like these guys
show up every day either. $17.00
http://oldetoolshop.com/forsale/dec/earlyhammer1201a.jpg
http://oldetoolshop.com/forsale/dec/earlyhammer1201b.jpg
http://oldetoolshop.com/forsale/dec/earlyhammer1201c.jpg
Deep 7/16 Inch Gouge Chisel Hand Forged From A File. Measuring 7 7/8"
long, 7/16" wide across the outside of the sweep at the edge, and this
weighs 3 oz unboxed. Not signed as to the maker. This is in reasonably
good condition and was cleaned. There is a little patina, but nothing
too bad. The outside of the sweep has some light pitting and frosting.
The edge will need a touch up. The striking end has a little
mushrooming. This ain't gotta fancy name, but it is neat tool that will
get the job done. $15.00
http://oldetoolshop.com/forsale/dec/hfgouge1201a.jpg
http://oldetoolshop.com/forsale/dec/hfgouge1201b.jpg
http://oldetoolshop.com/forsale/dec/hfgouge1201c.jpg
Snell & Atherton Cobblers Leather Sole Trimmer. Measuring 5 3/4" long
and this weighs 3 oz unboxed. This is in decent condition and was
cleaned. There is some light pitting on the head. The blade is fairly
good other than some frosting and staining, but the edge will need a
touch up. The screw works. The handle has some stains and dings, but
it's solid. This ain't minty, but it will get the job done. $15.00
http://oldetoolshop.com/forsale/dec/leathertool1201a.jpg
http://oldetoolshop.com/forsale/dec/leathertool1201b.jpg
http://oldetoolshop.com/forsale/dec/leathertool1201c.jpg
Early Hand Forged Denglestock PA Dutch Scythe Sharpening Anvil.
Measuring 7" long, the face is 1 1/8" wide, and this weighs 1 lb 1 1/2
oz unboxed. Not signed as to the maker. This is in decent condition
and was cleaned. There is some overall patina. The face also has some
light pitting with a slightly deeper bit at the one end, but nothing
that can't be dressed out. The spike is short, but that's how this was
made. This ain't pristine, but for a tool of this age it sure ain't bad
and it will get the job done. $25.00
http://oldetoolshop.com/forsale/dec/denglestock1201a.jpg
http://oldetoolshop.com/forsale/dec/denglestock1201b.jpg
http://oldetoolshop.com/forsale/dec/denglestock1201c.jpg
L S Starrett No 27 5 Inch Firm Joint Machinist Inside Calipers.
Measuring 5 3/8" long and this weighs 1 3/4 oz unboxed. This is in
reasonably good condition and was cleaned. There is a little frosting
and some light scuffs on the legs, but nothing too bad. The joint is
good and holds position. The tips are also good. This ain't pristine,
but it will get the job done. $14.00
http://oldetoolshop.com/forsale/dec/machinisttool1201a.jpg
http://oldetoolshop.com/forsale/dec/machinisttool1201b.jpg
http://oldetoolshop.com/forsale/dec/machinisttool1201c.jpg
Collectible Tools
Vintage Brass Pie Crimper Crimping Wheel With Rosewood Handle. Measuring
5 1/8" long, the wheel is 1 1/16" in diameter, and this weighs 1 oz
unboxed. Not signed as to the maker. This is in reasonably good
condition for the age and was not cleaned. The brass is good and the
wheel spins freely. The rosewood handle has a check on the one side and
some chips on the turned areas below the ferrule. The shaft is in
tight. I gotta say that these guys are sure few and far between. $35.00
http://oldetoolshop.com/forsale/nov/earlypiewheel1101a.jpg
http://oldetoolshop.com/forsale/nov/earlypiewheel1101b.jpg
http://oldetoolshop.com/forsale/nov/earlypiewheel1101c.jpg
Hand Forged Pruning Shears. Measuring 13 5/8" long, the jaws are 2 1/8"
deep, and this weighs 1 lb 7 1/4 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There is some
light pitting and overall patina. The jaws are good, although the edge
could stand a touch up. The joint is also good with no play. The one
handle does have a repair to it, but it's solid. I gotta say, that hand
forged tools of this style rarely show up, this is like the 3rd that I
have seen in all the years that I have been doing this. $27.00
http://oldetoolshop.com/forsale/nov/hfpruningshears1101a.jpg
http://oldetoolshop.com/forsale/nov/hfpruningshears1101b.jpg
http://oldetoolshop.com/forsale/nov/hfpruningshears1101c.jpg
http://oldetoolshop.com/forsale/nov/hfpruningshears1101d.jpg
Early Hand Forged 1/2 Inch Lathe Tool Gouge. Measuring 5 3/8" from the
edge to the top of the handle, the blade is 2" long, 1/2" wide across
the outside of the sweep, this is 12 1/2" overall, and this weighs 5 3/4
oz unboxed. Not signed as to the maker, but it does look to be 18th or
early 19th Century as to the age. This is in decent condition and was
cleaned. The inside of the sweep has some very light pitting. The back
has some voids left over from when this was made. There is a forge weld
line where the head meets the shaft, but this isn't cracked. The oak
handle looks to be original to the tool. That does have a check on the
back and a few smaller spots where the grain has opened up, but it feels
solid enough. This ain't pristine, but tools of this age with the
original handle are sure few and far between of late. $20.00
http://oldetoolshop.com/forsale/oct/earlychisel1001a.jpg
http://oldetoolshop.com/forsale/oct/earlychisel1001b.jpg
http://oldetoolshop.com/forsale/oct/earlychisel1001c.jpg
Machinist Tools
L S Starrett No 272 A Fillet Radius Gauge Or Gage. This weighs 1 1/4 oz
unboxed. This is in reasonably good condition and was cleaned. All the
leaves are present. They have some scuffs and oil stains, but the edges
are good and the sizes are all readable. The joints are a little
stiff. The handle has a little frosting. This ain't perfect, but it
will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/machinisttool1126a.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1126b.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1126c.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1126d.jpg
L S Starrett No 74 Fay Pattern 6 Inch Inside Caliper. Measuring 6
11/16" long and this weighs 2 1/4 oz unboxed. Robert J. Simpson and
Laroy S. Starrett of Athol, MA were granted Pat. No. 793,850 on July 4,
1905 for the design of the split quick nut used on this tool. This is in
decent condition and was cleaned. There is some frosting and spots of
light pitting on the legs. The joint is good as are the tips. The quick
nut works and the screw threads were oiled. This ain't pristine, but it
will get the job done. $15.00
http://oldetoolshop.com/forsale/nov/machinisttool1111a.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1111b.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1111c.jpg
Wm Johnson Newark 5 Inch Wing Compass Or Divider. Measuring 5 3/16"
long (from the tips to the top of the joint) and this weighs 3 3/4 oz
unboxed. This is in reasonably good condition and was cleaned. There is
a little frosting and a couple of dots of patina, but nothing too bad.
The joint is good. The tips are also good, although this was a longer
tool at some point in it's life. The locking screw and fine adjuster
nut both work. This ain't minty, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/nov/divider1102a.jpg
http://oldetoolshop.com/forsale/nov/divider1102b.jpg
http://oldetoolshop.com/forsale/nov/divider1102c.jpg
Globemaster No 5955 5 Inch Vernier Caliper & Case. Measuring 7 3/16"
overall and this all weighs 3 1/4 oz unboxed. Made in Spain. This is in
reasonably good condition and was cleaned. There are some light spots
of patina, but nothing too bad. The jaws are good. The slide moves
smoothly and the lock works. The case has some dust and funky on the
outside. This ain't perfect, but it is a handy tool that will get the
job done. $15.00
http://oldetoolshop.com/forsale/nov/machinisttool1109a.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1109b.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1109c.jpg
Helios Germany Machinist Screw Thread Pitch Gage Or Gauge. This weighs
1 3/4 oz unboxed. This is in good condition and was not cleaned. The
body and locks are good. The blades have some scuffs and a little oil
staining, but all are present and are good to go. This is a handy and
quality tool to have around. $15.00
http://oldetoolshop.com/forsale/nov/machinist1106a.jpg
http://oldetoolshop.com/forsale/nov/machinist1106b.jpg
http://oldetoolshop.com/forsale/nov/machinist1106c.jpg
Tabor Mfg Co 4 Inch 1885 Patent Speed Indicator. Measuring 4" long and
this weighs 2 1/2 oz unboxed. Harris Tabor of New York, NY was granted
Pat. No. 325,991 on Sept. 8, 1885 for the design of this tool. This is
in reasonably good condition and was cleaned. The body has a few dots
and some scuffs but nothing too bad. The plating on the wheel is worn a
little on the front and a little more on the back. The spring loaded
tip is good and this spins freely. This ain't pristine but it is not a
very common tool, at least in my travels. $30.00
http://oldetoolshop.com/forsale/nov/machinisttool1107a.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1107b.jpg
http://oldetoolshop.com/forsale/nov/machinisttool1107c.jpg
Rabone No 19 24 Inch Patternmakers Shrink Rule. Measuring 25 1/4"
overall, this has Standard and brass contraction scales on the front,
single and double contraction scales for iron on the back, and this
weighs 7 oz unboxed. This is in reasonably good condition and was
cleaned. There is some staining and small spots of frosting and light
pitting on both sides. All the rulings are readable and the edges and
corners are good. This ain't pristine, but it is a quality tool and
these guys sure do not show up every day. $35.00
http://oldetoolshop.com/forsale/oct/shrinkrule1001a.jpg
http://oldetoolshop.com/forsale/oct/shrinkrule1001b.jpg
http://oldetoolshop.com/forsale/oct/shrinkrule1001c.jpg
Uncommon L S Starrett No 44 6 Inch Double Caliper. Measuring 6 1/4"
long and this weighs 3 1/4 oz unboxed. This has one of the earlier
Starrett marks. This is in reasonably good condition and was cleaned.
There are some scuffs and frosting on the arms and a user mark on the
one upper arm. The joints are all good and hold position. The caliper
tips are good save for a little patina. The one divider tip is a little
shorter than the other one and is slightly bent. This ain't pristine,
but these guys rarely are, and overall this one sure ain't bad. $28.00
http://oldetoolshop.com/forsale/aug/machinisttool0809a.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0809b.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0809c.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0809d.jpg
L S Starrett No 76 4 Inch Fay Pattern Thread Caliper. Measuring 4 5/8"
long and this weighs 1 3/4 oz unboxed. Charles P. Fay of Springfield,
MA was granted Pat. No. 319,215 on June 2, 1885 for the design of this
tool and Laroy S. Starrett of Athol, MA was granted Pat. No. 642,170 on
Jan. 30, 1900 for the design of the split nut. This is in decent
condition and was cleaned. There is some frosting on the arms and a
little funky on the inside of the joint. The spring and joint are
good. The tips don't meet quite flush when closed. The nut turns okay,
but the quick set doesn't want to work. This is missing the ball on the
end of the screw. This sure ain't minty, but then tools that are 100
plus years old rarely are and this will get the job done. $26.00
http://oldetoolshop.com/forsale/aug/machinisttool0808a.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0808b.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0808c.jpg
http://oldetoolshop.com/forsale/aug/machinisttool0808d.jpg
Woodworking Tools
Vintage Tool Handle With 4 Bits. Measuring 3 1/4" long and this weighs
2 1/2 oz unboxed. Not signed as to the maker, this is just marked
Germany. This is in reasonably good condition and was not cleaned.
There are a few spots on the body where the plating is worn, but almost
all of it is present. The screw threads and notch that serves to hold
the bits is good. The four bits are also good, other the tip of the awl
being bent a little and the plating on the screwdriver tip has a little
wear. This ain't pristine, but it's a neat little tool set. $14.00
http://oldetoolshop.com/forsale/nov/toolhandle1102a.jpg
http://oldetoolshop.com/forsale/nov/toolhandle1102b.jpg
Red Head Mfg New York No 110 Eggbeater Hand Drill. Measuring 12" long
and this weighs 1 lb 6 oz unboxed. This is in reasonably good condition
and was not cleaned. The chuck is good. There is a little wear to the
finish on the frame and the gear wheel. The handle also has some wear
to the finish and somebody marked an X on the cap, but the threads are
good. There are 8 bits in the handle. This ain't perfect, but it will
get the job done. $22.00
http://oldetoolshop.com/forsale/nov/ebdrill1101a.jpg
http://oldetoolshop.com/forsale/nov/ebdrill1101b.jpg
http://oldetoolshop.com/forsale/nov/ebdrill1101c.jpg
Stanley Yankee No 3423 Phillips Reversible Screwdriver. This weighs 1
1/4 oz unboxed. This is in good condition and was not cleaned. Other
than a couple of stains and light scuffs, there ain't nothing much
patina wise to fuss about. Both tips are good. The ratchet works in
both directions, but could stand a drop of oil. This ain't minty, but
it's pretty darn close. $14.00
http://oldetoolshop.com/forsale/nov/yankee1104a.jpg
http://oldetoolshop.com/forsale/nov/yankee1104b.jpg
Stearns Wheeler Patent Wood Countersink Brace Bit. Measuring 4 1/8"
long, the head is 7/8" in diameter, and this weighs 1 1/2 oz unboxed.
Asa Wheeler of Battleborough, VT was granted Pat. No. 101,796 on Apr.
12, 1870 for the design of this tool which was made by him originally
and later other companies. This is in reasonably good condition and was
cleaned. About the only patina is a little ringing on the head. The
edge feels good to the touch. The tang is also good to go. This ain't
pristine, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/bracetool1107a.jpg
http://oldetoolshop.com/forsale/nov/bracetool1107b.jpg
L Watts NY Hand Forged Ships Carpenters Adze Head. Measuring 9 1/2"
long (straight across), the edge is 3 3/4" wide, and this weighs 2 lbs 4
3/4 oz unboxed. Lewis H Watts was a New York NY edge tool maker and
tool dealer who worked from 1843 until 1885. This is in decent
condition and was cleaned. There is some overall light patina and
pitting. The face has some dots of light pitting and the edge will need
some work. The hammer poll has a whisker of mushrooming, but overall
that is good. I did run a file over some mushrooming at the top of the
eye, that ain't perfect, but it's better than it was. The eye is
otherwise good with no cracks that I can see. This ain't minty, but
considering that it's over 136 years old, well it sure ain't bad. $40.00
http://oldetoolshop.com/forsale/nov/adze1101a.jpg
http://oldetoolshop.com/forsale/nov/adze1101b.jpg
http://oldetoolshop.com/forsale/nov/adze1101c.jpg
http://oldetoolshop.com/forsale/nov/adze1101d.jpg
Four Stanley Spokeshave Bodies TO RESTORE. There are 3 No. 51's, one
No. 52, and they weigh 2 lbs 1 oz unboxed. These are in as found
condition and were not cleaned. There is some wear to the finish on the
bodies, some rusting, and other patina. The soles have some light
rusting, but that should clean off okay. They all have the screws for
the blades and caps and all of those work. These will need caps and
blades, I don't have any here, otherwise I would clean these guys up,
eh? These will need some parts and work, but they are good tools. $55.00
http://oldetoolshop.com/forsale/nov/spokeshave1101a.jpg
http://oldetoolshop.com/forsale/nov/spokeshave1101b.jpg
http://oldetoolshop.com/forsale/nov/spokeshave1101c.jpg
http://oldetoolshop.com/forsale/nov/spokeshave1101d.jpg
Vintage No 6 3/8 Inch Brace Dowel Bit. Measuring 5" long, the cut is
3/8" in diameter, and this weighs 1 1/4 oz unboxed. Not signed as to
the maker. This is in reasonably good condition and was cleaned. There
is a little patina, but nothing too bad. The spurs, lead screw, and
cutters are all good. The tang has a few light dings. This ain't
minty, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/bracetool1104a.jpg
http://oldetoolshop.com/forsale/nov/bracetool1104b.jpg
North Bros Yankee No 2150 Brace Auger Bit Extension. Measuring 15 3/4
long (fully extended), 14 15/16" when closed, and this weighs 14 1/2 oz
unboxed. George O. Leopold and Thomas J. Fegley of Philadelphia, PA
were granted Pat. No. 1,661,935 on March 6, 1928 for the design of this
tool. This one is marked Pat. Pending so it was made prior to that.
This is in reasonably good condition and was cleaned. The head has some
frosting, but nothing too bad patina wise. The chuck works, although
the threads could stand a little oil. The shaft and tang have some
light staining, but have most of the plating. This ain't pristine, but
it's a quality tool that will get the job done. $20.00
http://oldetoolshop.com/forsale/nov/bracetool1105a.jpg
http://oldetoolshop.com/forsale/nov/bracetool1105b.jpg
Stanley Handyman No 1226 1/2 Inch Brace Screwdriver Bit. This weighs 2
oz unboxed. This is NOS (that's New Old Stock) but it wasn't stored
someplace nice. There are some dots of light patina. The tip and tang
are good other than some staining. This is a hard to find larger size.
$12.00
http://oldetoolshop.com/forsale/nov/bracetool1103a.jpg
http://oldetoolshop.com/forsale/nov/bracetool1103b.jpg
Hand Forged 1 1/4 Inch Firmer Chisel. Measuring 6 5/8" from the edge to
the top of the handle, the blade is 4 1/4" long, this is 10 5/8"
overall, and this weighs 12 oz unboxed. Not signed as to the maker.
This is in decent condition and was cleaned. The back is fairly good
other than some spots and dots. The top has some pitting and scuffs
left over from when this was made. The handle has some checks at the
end and probably would benefit from a bang ring. This ain't pristine,
but it's a solid older tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/nov/chisel1102a.jpg
http://oldetoolshop.com/forsale/nov/chisel1102b.jpg
Sears No 935892 3 Piece Wood Chisel Set & Case. There is a 1/2", a
3/4", a 1", and they weigh 14 3/4 oz unboxed. These are in used
condition and were cleaned. The 1/2" is good all around on the blade.
the 3/4" has light pitting and dings on the back and the top, and the 1"
has some frosting on the back. All of the edges have chips and will
need some work. The handles have some worn spots. The case is good save
for a little shop patina. These ain't the best ones around, but for a
traveling tool box, they will work just fine. $18.00
http://oldetoolshop.com/forsale/nov/chiselset1101a.jpg
http://oldetoolshop.com/forsale/nov/chiselset1101b.jpg
http://oldetoolshop.com/forsale/nov/chiselset1101c.jpg
http://oldetoolshop.com/forsale/nov/chiselset1101d.jpg
http://oldetoolshop.com/forsale/nov/chiselset1101e.jpg
Craftsman No 9-39485 8 Inch Adjustable Bevel Square. This weighs 3 1/2
oz unboxed. This is a Craftsman branded Stanley No. 25 TB. This is in
decent condition and was cleaned. The blade has some frosting on the
plating, mainly around the slot, and a couple of dots of patina. There
is a user name marked along the slot and on a couple of the brass handle
plates. The edges and corners are good. The handle has some stains, but
it's solid. This ain't minty, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/square1102a.jpg
http://oldetoolshop.com/forsale/nov/square1102b.jpg
http://oldetoolshop.com/forsale/nov/square1102c.jpg
http://oldetoolshop.com/forsale/nov/square1102d.jpg
Vintage Universal Bevel Square. The blade is 5 1/2" long and this
weighs 3 1/2 oz unboxed. This is in reasonably good condition and was
cleaned. The blade is clean on the ruled side and has a little frosting
on the back. The rulings are readable and the edges and corners are
good. The die-cast handle has some light patina, but the edges and
corners are also good. The locking screw works. This is a neat little
tool that will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/square1101a.jpg
http://oldetoolshop.com/forsale/nov/square1101b.jpg
http://oldetoolshop.com/forsale/nov/square1101c.jpg
Vintage Tapered Reamer Brace Auger Bit. Measuring 4 13/16" long, 3/8"
square at the start of the tang, and this weighs 2 oz unboxed. Not
signed as to the maker. This is in reasonably good condition and was
cleaned. There ain't much in the way of patina other than some light
scuffs and staining. The edges are good as is the tang. This ain't got
a fancy name, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/oct/bracetool1003a.jpg
http://oldetoolshop.com/forsale/oct/bracetool1003b.jpg
AMT No C300 Wood Carvers Screw Set. This all weighs 2 lbs 3 1/4 oz
unboxed. This is NOS (that's New Old Stock) and was not cleaned. This
for soft woods, like bass wood and pine. There are 3 different screw
sizes for your pleasure. The box is a bit beat up, but the tools are
all good. This ain't top of the line, but it will get the job done. $27.00
http://oldetoolshop.com/forsale/sept/carverscrew0901a.jpg
http://oldetoolshop.com/forsale/sept/carverscrew0901b.jpg
North Bros No 3180 Drill Bit Adapter Yankee 31/131 Screwdriver. This
weighs 1/2 oz unboxed. Zachry T. Furbish of Philadelphia, PA was
granted Pat. No. 666,509 on Jan. 22, 1901 for the design of this tool
which was made by the North Bros. This will fit the Yankee No. 31 and
131 push screwdrivers along with the A models. This is in reasonably
good condition and was cleaned. There ain't much in the way of patina
to fuss about. The hole is clear and the spring is good. These guys
sure are had to come by any more. $14.00
http://oldetoolshop.com/forsale/oct/yankee1001a.jpg
http://oldetoolshop.com/forsale/oct/yankee1001b.jpg
Auburn Tool No 189 1 1/8 Inch Toted Nosing Plane. Measuring 12 1/16"
long across the sole, the cut is 1 1/16" (this is marked 1 1/8")and this
weighs 1 lb 11 1/2 oz unboxed. This is in reasonably good condition and
was cleaned. Overall the body is good other than a few light stains and
a couple of very thin checks on the top. The tote is good. The sole
has a little chipping on the ends at the toe, but after that it's good
and the mouth is factory tight. The iron is clean on the cutting face,
but will need a touch up on the edge. The wedge is also good. These
guys sure do not show up very often in this kind of shape. $30.00
http://oldetoolshop.com/forsale/oct/woodenplane1001a.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001b.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001c.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001d.jpg
TWO Wood River HSS Lathe Tools. The one on the left is a parting tool,
the blade is 1/2" wide, 6 11/16" long to the start of the handle, this
is 22 1/8" overall, the one on the right is a bowl scraper, the blade
is 3/4" wide, 5 7/8" long to the start of the handle, this is 21 1/4"
overall, and they weigh 1 lb 9 1/2 oz unboxed. Made In China. These
are in used, but reasonably good condition, and were cleaned. The
blades have some light scuffs and the tip of the parting tool is a
little discolored. Both edges will need a touch-up. Both handles have
some dings, but have almost all of the original finish, plus a coat of
wax. These ain't pristine, but they will get the job done at half the
price of what new ones cost. Look it up. $55.00
http://oldetoolshop.com/forsale/oct/lathetool1001a.jpg
http://oldetoolshop.com/forsale/oct/lathetool1001b.jpg
http://oldetoolshop.com/forsale/oct/lathetool1001c.jpg
Signed Vintage Wood Handle Saw Setting Wrest. Measuring 6 3/8" overall,
the head is 2 1/4" long, 1 1/4" wide at the area closest to the handle,
and this weighs 3 oz unboxed. This is signed, bit I can't read it.
This is in decent condition and was cleaned. The head has some light
pitting and frosting. The one notch has a little wear at the end and
the others are all good, save for a little crusty inside. The handle
has a burned spot at the top, a couple of checks on the sides, and an
assortment of dings and stains. The head is in tight. This ain't
pretty or perfect, but these guys rarely are and this one will get the
job done. $17.00
http://oldetoolshop.com/forsale/oct/sawtool1001a.jpg
http://oldetoolshop.com/forsale/oct/sawtool1001b.jpg
http://oldetoolshop.com/forsale/oct/sawtool1001c.jpg
http://oldetoolshop.com/forsale/oct/sawtool1001d.jpg
English 6 Inch Try Or Set Square. Measuring 7 11/16" overall, the blade
is 6 1/16" long, this is 5 1/4" high, and this weighs 7 3/4 oz unboxed.
Not signed as to the maker, just marked Made In England on the paper
label. This is in good condition and was lightly cleaned. I took some
light rust off of the front of the blade with some fine steel wool.
There are a few small spots where the bluing is worn. The back of the
blade is good. All the corners and edges are crispy, including the
handle. The finish on the handle is also perfect. This is a good
looking tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/oct/square1004a.jpg
http://oldetoolshop.com/forsale/oct/square1004b.jpg
http://oldetoolshop.com/forsale/oct/square1004c.jpg
http://oldetoolshop.com/forsale/oct/square1004d.jpg
Vintage Rosewood Marking Gage Or Gauge. The beam is 8 5/16" long and
this weighs 2 3/4 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. The beam has some wear under the
point and some dings from the screw on the top. There are some tiny
bits of paint down in the grain that didn't want to come off and a user
name marked on the back. The point is an old nail, but it does the
job. The head also has some wear, but it's solid and the boxwood screw
is good and does the job. This ain't the prettiest, but it's an older
tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/oct/markinggage1001a.jpg
http://oldetoolshop.com/forsale/oct/markinggage1001b.jpg
http://oldetoolshop.com/forsale/oct/markinggage1001c.jpg
http://oldetoolshop.com/forsale/oct/markinggage1001d.jpg
Blacksmith & Hammers
Two Hand Forged Blacksmith Tongs TO RESTORE. The one on the left is 11
5/8" long, the jaws are 1 1/4" deep, 1" wide at the tips, the one on the
right is 11 3/4" long, the jaws are 2 3/4" deep, 5/8" wide at the tips,
and they weigh 2 lbs 1 1/4 oz unboxed. Not signed as to the maker.
These are in TO RESTORE condition and were cleaned. The one on the left
has some small checks around the jaws. The joint has lots of wiggle,
but the rivet is solid. The forge weld where the one handle meets the
jaw below the joint is starting to open a little and the one handle has
some roughness and chipping on the end. The jaws on the one on the left
are fairly good and joint has just a little play. The forge weld at the
center of the one handle is starting to open up. These sure ain't
pretty or perfect and they will need some work, but that will take less
time than making new ones. $32.00
http://oldetoolshop.com/forsale/nov/blacksmith1106a.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1106b.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1106c.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1106d.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1106e.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1106f.jpg
Long Small Jaw Hand Forged Blacksmith Tongs. Measuring 20 5/8" long,
the jaws are 1 1/8" deep, 5/16" wide at the tips, and this weighs 2 lbs
6 1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is the usual patina found on these
guys. The jaws are good and are slightly hollowed across the centers.
The joint has some play and the rivet could stand a little "adjusting".
The handles are good to go. This ain't minty, but this sure ain't the
most common pair of tongs that I have come across. $22.00
http://oldetoolshop.com/forsale/nov/blacksmith1103a.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1103b.jpg
http://oldetoolshop.com/forsale/nov/blacksmith1103c.jpg
Small Ball Peen 4 1/2 Oz Hammer Head. Measuring 2 5/8" long, the face
is 3/4" in diameter, the peen is 11/16" in diameter, and this weighs 4
1/2 oz unboxed. Marked with a M and either a 76 or 78. This is New Old
Stock that got left out in the rain and was cleaned. The sides have
some frosting, but nothing too bad patina wise. The face and peen are
also have some light patina. The eye is ready to drop on a handle.
This will need a little work, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/oct/hammer1005a.jpg
http://oldetoolshop.com/forsale/oct/hammer1005b.jpg
http://oldetoolshop.com/forsale/oct/hammer1005c.jpg
Blacksmith Hand Forged Hammer Eye Drift Punch Head. Measuring 7 1/2"
long, the tip is roughly 11/16" high, 5/16" wide, and this weighs 1 lb
15 1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall pitting and patina. I
did run a file over some mushrooming on the tip, but it is flared a
little and could stand some more dressing. The punch has a very slight
bend to one side. There is a visible forge weld line where the punch
meets the body, but this ain't cracked. The striking end has some
mushrooming and a couple of shallow checks, but nothing too bad. The
punched eye has a ding or cut mark on the underside at the rear, but
it's not cracked. This sure ain't perfect, but it ain't like these guys
show up every day and with a little work it will get the job done. $24.00
http://oldetoolshop.com/forsale/oct/blacksmith1003a.jpg
http://oldetoolshop.com/forsale/oct/blacksmith1003b.jpg
http://oldetoolshop.com/forsale/oct/blacksmith1003c.jpg
Blacksmith Hand Forged Slag Chipping Hammer Head. Measuring 8 1/2"
long, the vertical edge is 7/8" high, other one is 1" wide, and this
weighs 1 lb 7 1/4 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. There is a little patina,
but nothing too bad. There are a few spots of light pitting and some
scuffs left over from when this was made. Both edges are good and were
dressed recently. The punched eye is good to go. This ain't minty, but
it sure ain't bad and it will get the job done. $18.00
http://oldetoolshop.com/forsale/sept/blacksmith0903a.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0903b.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0903c.jpg
Everything Else
Crescent Tool 4 Inch Adjustable Wrench. This weighs 1 3/4 oz unboxed.
This is in decent condition and was cleaned. There are some dings and
wear. The jaws have some tiny dings on the edges, but the faces are
good and the adjuster travels the full distance. The handle also has
some tiny dings. T'was the tool of a working man. This ain't perfect,
but it is a solid tool that will get the job done. $14.00
http://oldetoolshop.com/forsale/nov/wrench1101a.jpg
http://oldetoolshop.com/forsale/nov/wrench1101b.jpg
http://oldetoolshop.com/forsale/nov/wrench1101c.jpg
W & C Wynn No 4 Cobblers Lasting Pliers. Measuring 8 5/16" long, the
jaws are 1/2" wide, and this weighs 11 1/2 oz unboxed. The W & C Wynn
Company was a long time Birmingham England maker of leather and other
tools who merged with R Timmins & Son in 1887, so this was made before
that. This is in decent condition and was cleaned. There is some
pitting and patina, some of it light, some of it not so light. The jaws
have a little wear and some rust down in the grooves, but there is
plenty there to work with. The hammer face has a little mushrooming as
does the top of the upper jaw. The "through the center" joint has a
little crusty inside and a wee bit of wiggle. The handles are good save
for the patina. This ain't pristine, but seeing as it's, at the very
least, 135 yars old, well it ain't too bad, and it will get the job
done. $24.00
http://oldetoolshop.com/forsale/oct/leathertool1001a.jpg
http://oldetoolshop.com/forsale/oct/leathertool1001b.jpg
http://oldetoolshop.com/forsale/oct/leathertool1001c.jpg
http://oldetoolshop.com/forsale/oct/leathertool1001d.jpg
Flexco Xtra-life No S2S Brace Spanner Wrench. Measuring 4 3/16" long,
the head is 13/16" wide, 1/4" wide across the inside of the tips, and
this weighs 4 oz unboxed. This is in used but reasonably good condition
and was not cleaned. There is some staining and a little wear to the
finish. The tips have a little wear, but there is plenty there to work
with. The tang is good. This ain't pristine, but it is a neat tool
that will get the job done. $14.00
http://oldetoolshop.com/forsale/oct/bracetool1005a.jpg
http://oldetoolshop.com/forsale/oct/bracetool1005b.jpg
Sargent & Co 1884 Patent Tool Handle With 10 Bits. Measuring 5 7/8"
long and this weighs 5 3/4 oz unboxed. Granville W. Wright of New
Haven, CT was granted Pat. No. 303,478 on Aug. 12, 1884 for the design
of this tool which was made by Sargent & Co. This is in reasonably good
condition and was lightly cleaned. The plating has some spots of rust,
but most of it is present except on the one side of the chuck nut. The
jaws have a little patina down inside, but the nut works. The maple
handle has some stains and light scratches, but has almost all of the
original finish plus a coat of wax. The threads on the cap are good.
This comes with the 10 original bits. Those are all good othe than the
screw starter which is bent a little. I gotta say, that finding one of
these in this kind of shape is sure getting hard to do. $22.00
http://oldetoolshop.com/forsale/oct/toolhandle1001a.jpg
http://oldetoolshop.com/forsale/oct/toolhandle1001b.jpg
http://oldetoolshop.com/forsale/oct/toolhandle1001c.jpg
Stortz Acme No 226 Cement Plaster Mason Corner Tool. Measuring 5 11/16"
long and this weighs 1 lb 1 1/2 oz unboxed. This is in reasonably good
condition and was cleaned. The faces have some staining and a few spots
that look like casting flaws. The center edge is good and straight.
The inside of the body has almost all of the original finish. The
handle has some stains and dings, but it's solid. This ain't pristine,
but it is a quality tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/sept/cementtool0901a.jpg
http://oldetoolshop.com/forsale/sept/cementtool0901b.jpg
http://oldetoolshop.com/forsale/sept/cementtool0901c.jpg
http://oldetoolshop.com/forsale/sept/cementtool0901d.jpg
-----------------------------------------
"Aging can be fun if you lay back and enjoy it."
Clint Eastwood
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
|
