Howdy. Well summer has sure landed with a vengeance. Hot and humid
from sunrise to well past sunset (and yes I know that there are a lot of
places hotter than here, but...) The fleas have been sporadic, but
I've managed to land some really nice collectible and some solid user
tools as well. Lots of fresh goodies on here since the previous list.
PayPal is preferred (if you use it) on all items. It's easier for me to
ship items off of a paid PayPal invoice, especially First Class ones.
Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
------------------------------------------------------
Columbian Hardware Co 4 Inch Blacksmith Leg Vise. Measuring about 40"
high, the jaws are about 4 3/8" wide, and this weighs about a whole
bunch of lbs unboxed. This is in decent condition and was not cleaned.
Been a while since I last did one of these "on the back of the truck
photo sessions..) Lots of grime and patina going on this guy. The jaws
are fairly good and close up tight and flush on the tops, but not quite
flush on the sides. The screw is missing a section from the end, but
the jaws open to 3" with no problem. The nut is good (that is a sprue
line showing in the last picture and not a crack.) The bench mount is
solid and the spring is good. This ain't perfect, but seeing as what
they are selling for on other places, for the money this will get the
job done. PICKUP ONLY at my shop here in NE PA. This guy is too heavy
and well gnarly for me to ship. $150.00
http://oldetoolshop.com/forsale/july/blacksmithvise0701a.jpg
http://oldetoolshop.com/forsale/july/blacksmithvise0701b.jpg
http://oldetoolshop.com/forsale/july/blacksmithvise0701c.jpg
http://oldetoolshop.com/forsale/july/blacksmithvise0701d.jpg
http://oldetoolshop.com/forsale/july/blacksmithvise0701e.jpg
http://oldetoolshop.com/forsale/july/blacksmithvise0701f.jpg
Vintage Hammacher Schlemmer & Co Bow Drill. Measuring 10 1/4" long, the
chuck is 3/8" in diameter, and this weighs 1 lb 10 1/2 oz unboxed. Bacck
in the 19th and early part of the 20th Century, Hammacher Schlemmer & Co
were major resellers of woodworking and other tools. This is in good
condition and was cleaned. There ain't nothing much overall patina wise
to fuss about. The chuck is good. This would have used bits that were
mounted into metal pads that would have been secured with a metal pin.
I did NOT get any bits with this guy. The brass center section is good
and the handle ferrule is also good other than a scratch marked user
name. The side screw works and the head section spins freely. I did
put a little oil down in there. I can't say what kind of wood the
handle is, but it does not look to be rosewood. That is good and has
almost all of the original finish, plus a coat of wax. This is one of
those tools that is few and very far between. $135.00
http://oldetoolshop.com/forsale/june/bowdrill0601a.jpg
http://oldetoolshop.com/forsale/june/bowdrill0601b.jpg
http://oldetoolshop.com/forsale/june/bowdrill0601c.jpg
J S Cantelo 1883 Patent 8 Inch Folding Handle Draw Knife Or Drawknife.
Measuring 16" overall, the blade is 8 1/16" long, 1 3/16" wide across
the edge, and this weighs 1 lb 12 oz unboxed. John Solomon Cantelo of
Taunton, MA was granted Pat. No. 286,385 on Oct. 9, 1883 for the design
of this tool, which was the first of five patents that he was issued for
draw knives. This is in reasonably good condition and was cleaned.
There is some staining and some spots of frosting on the back, but
nothing too bad. The edge is fairly good and the top was never struck.
The front has more of the same light patina as the back. The handles
are good and have almost all of the original finish, plus a coat of
wax. The handle hardware has some frosting and there is a user mark
stamped on both sides. Both handles move freely, but they wiggle around
a little when they are in the working position. This ain't pristine,
but seeing as how it's at least 120 years old, it sure ain't bad. $60.00
http://oldetoolshop.com/forsale/july/drawknife0701a.jpg
http://oldetoolshop.com/forsale/july/drawknife0701b.jpg
http://oldetoolshop.com/forsale/july/drawknife0701c.jpg
http://oldetoolshop.com/forsale/july/drawknife0701d.jpg
TWO Mahogany Wood Scraper Planes. The one on the left has a flat sole
and is 8 9/16" long, the blade is 2 13/16" wide, the one on the right
has a convex sole and is 7 1/4" long, the blade is 2 1/2" wide, and they
weigh 1 lb 2 oz unboxed. There is a user mark on the left one, but
these were made by the same hand. These are in good condition and were
cleaned. Overall the bodies are good as are the soles. All the screws
work and hold. The left blade isn't sighed, the right one is a
Disston. The left one has some light patina on the top on both sides,
but the face is clean, and the right one is good overall. Both have
hooks turned on the edge. I gotta say, that this is a good looking pair
of tools that will get the job done. $55.00
http://oldetoolshop.com/forsale/july/woodenscraperplane0701a.jpg
http://oldetoolshop.com/forsale/july/woodenscraperplane0701b.jpg
http://oldetoolshop.com/forsale/july/woodenscraperplane0701c.jpg
http://oldetoolshop.com/forsale/july/woodenscraperplane0701d.jpg
http://oldetoolshop.com/forsale/july/woodenscraperplane0701e.jpg
http://oldetoolshop.com/forsale/july/woodenscraperplane0701f.jpg
ELEVEN Vintage Silversmith Pattern Stamps. They range in length from 1
3/4" to 3 1/8" and they weigh 11 oz unboxed. Two are marked R Hoe New
York, one is a P S Stubs Cast Steel, and the rest aren't signed. There
are an assortment of faces, the two rectangular ones are a wee bit
different in size. These are in decent condition and were cleaned. The
faces are good for the most part save for a little wear and some light
patina. All of the striking ends did have some mushrooming removed,
some was light, and some was pretty nasty. That ain't a super pretty
job, but they are better and safer than they were. I gotta say that
these guys are sure getting few and very far between any more. $135.00
http://oldetoolshop.com/forsale/july/silversmithtool701a.jpg
http://oldetoolshop.com/forsale/july/silversmithtool701b.jpg
http://oldetoolshop.com/forsale/july/silversmithtool701c.jpg
http://oldetoolshop.com/forsale/july/silversmithtool701d.jpg
P S & W 18 Inch Blacksmith Signed Wing Divider. Measuring 18 1/2" long
(from the tips to the top of the joint) and this weighs 1 lb 14 oz
unboxed. I did a search, but nothing shows up for Mr. Graver. This is
in decent condition and was cleaned. There is some overall light
patina, including frosting and some spots of light pitting. The joint
and tips are good. The locking screw is original, and that and the fine
adjustment nut both work and were oiled. This ain't pristine, but these
big ones are sure getting few and far between, especially blacksmith
marked. Just saying. $85.00
http://oldetoolshop.com/forsale/july/divider701a.jpg
http://oldetoolshop.com/forsale/july/divider701b.jpg
http://oldetoolshop.com/forsale/july/divider701c.jpg
http://oldetoolshop.com/forsale/july/divider701d.jpg
http://oldetoolshop.com/forsale/july/divider701e.jpg
Blade 1/2 Inch For A Stanley No 71 Router Plane. Measuring 3 1/16"
high, the blade is 1 3/16" long, 1/2" wide. and this weighs 1 3/4 oz
unboxed. This is in good condition and was cleaned. The face of the
blade is clean and there is lots to work with, but the edges will need
some work. The adjuster notch is also good. These guys are sure
getting few and far between any more. $32.00
http://oldetoolshop.com/forsale/june/planepart0601a.jpg
http://oldetoolshop.com/forsale/june/planepart0601b.jpg
http://oldetoolshop.com/forsale/june/planepart0601c.jpg
Keuffel & Esser K & E Mercury Drafting Tool Set & Case. This all weighs
15 3/4 oz unboxed. This is in very good condition and was not cleaned.
I doubt that it was used very much if at all. The tools are all pristine
and everything is present. There is a little wear to the edges of the
case, but it's solid. This is about as close to minty as these guys
come. $27.00
http://oldetoolshop.com/forsale/july/draftingtoolse0701a.jpg
http://oldetoolshop.com/forsale/july/draftingtoolse0701b.jpg
http://oldetoolshop.com/forsale/july/draftingtoolse0701c.jpg
http://oldetoolshop.com/forsale/july/draftingtoolse0701d.jpg
Stanley No 70 Slitting Gage Or Gauge. This weighs 4 3/4 oz unboxed.
This is in decent condition and was cleaned. The beam has some
staining, dings, scuffs, and a little wear at the working end. All the
rulings are readable and the beam is straight. The point screw works
and the tip is fairly good. There is a fair amount left and it will
need a touch up. The head also has some stains, dings, and a little
wear. The locking screw has some dings, but it works and holds. This
ain't perfect, but these guys are sure few and very far between of
late. $30.00
http://oldetoolshop.com/forsale/july/stanley700701a.jpg
http://oldetoolshop.com/forsale/july/stanley700701b.jpg
http://oldetoolshop.com/forsale/july/stanley700701c.jpg
http://oldetoolshop.com/forsale/july/stanley700701d.jpg
Vintage Hand Forged Box Or Crate Hammer. Measuring 10" overall, the
head is 3 3/4" long, the face is 7/16" square, the peen is 1/2" wide,
and this weighs 10 1/2 oz unboxed. Not signed as to the maker. This is
in decent condition and was cleaned. There is some overall light
patina. The face and peen have some dings and a bit of mushrooming on
both. There also is some mushrooming on the top of the head. The claws
are good. This ain't pretty or perfect, but considering the kinda life
it's lead, well it sure ain't bad. $18.00
http://oldetoolshop.com/forsale/july/hfcratehammer0701a.jpg
http://oldetoolshop.com/forsale/july/hfcratehammer0701b.jpg
http://oldetoolshop.com/forsale/july/hfcratehammer0701c.jpg
http://oldetoolshop.com/forsale/july/hfcratehammer0701d.jpg
Dixie Beer Co Advertising Carpenters Hatchet Bottle Opener. Measuring 4
1/4" long and this weighs 2 oz unboxed. This is in decent condition and
was cleaned. Whatever finish was on this originally had gotten a bit
funky. The opener end is good. This ain't perfect, but if you ever had
to pry a bottle top off with a pair of pliers, well this guy will get
the job done. $14.00
http://oldetoolshop.com/forsale/july/bottletool0701a.jpg
http://oldetoolshop.com/forsale/july/bottletool0701b.jpg
http://oldetoolshop.com/forsale/july/bottletool0701c.jpg
http://oldetoolshop.com/forsale/july/bottletool0701d.jpg
Vintage Iron Hand Vise Or Handvise. Measuring 5 1/4" long, the jaws are
1 1/2" wide, and this weighs 12 3/4 oz unboxed. Not signed as to the
maker. This is in reasonably good condition and was cleaned. There is
some frosting, but nothing too bad patina wise. The jaws have a few
light dings on the tops, but close down tight. There is a little bit of
the cross-hatching on the faces. The spring is on the light side, but
works. The joint does have some play. The nut and screw are good.
This ain't perfect, but it will get the job done. $27.00
http://oldetoolshop.com/forsale/july/handvise0701a.jpg
http://oldetoolshop.com/forsale/july/handvise0701b.jpg
http://oldetoolshop.com/forsale/july/handvise0701c.jpg
http://oldetoolshop.com/forsale/july/handvise0701d.jpg
http://oldetoolshop.com/forsale/july/handvise0701e.jpg
Vintage Small Wood Handle Turnscrew Or Screwdriver. Measuring 5 3/8"
long, the tip is 1/4" wide, and this weighs 1 oz unboxed. Not signed as
to the maker. This is in good condition and was cleaned. The blade is
clean save for a little light patina down by the ferrule. The tip is
good, but was dressed at some point. The handle has a few dings to the
one turning, but still has almost all of the original finish. This is a
good looking example of this tool to say the least. $20.00
http://oldetoolshop.com/forsale/july/turnscrew701a.jpg
http://oldetoolshop.com/forsale/july/turnscrew701b.jpg
http://oldetoolshop.com/forsale/july/turnscrew701c.jpg
Vintage Buck Bros 1/2 Inch Screwdriver Turnscrew Brace Bit. Measuring 4
7/8" long, the tip is 1/2" wide, and this weighs 1 1/2 oz unboxed. This
is in decent condition and was cleaned. The front has some staining and
frosting. The back has more of the same along with a patch of light
rust etching. The edge is good and was dressed at some point. The tang
has a wee bit of mushrooming, but nothing that will interfere with this
being used. This ain't minty, but it will get the job done. $14.00
http://oldetoolshop.com/forsale/june/bracetool0602a.jpg
http://oldetoolshop.com/forsale/june/bracetool0602b.jpg
http://oldetoolshop.com/forsale/june/bracetool0602c.jpg
Early Hand Forged Wig Hair Flat Iron. Measuring 11 3/8" long, the faces
are 1 5/8" wide, and this weighs 1 lb 1 1/4 oz unboxed. Not signed as
to the maker. Age, anywhere from the late 18th Century until the mid
19th Century. This is in decent condition and was cleaned. There is
some overall light pitting and patina. The faces also have some light
pitting, but close down tight. The "through the center" joint is good.
The loop handles have some pitting, and would have originally been
wrapped with cord, but that rarely survives the journey. This ain't
pristine, but these guys are sure not very common either. $30.00
http://oldetoolshop.com/forsale/june/earlywigiron0601a.jpg
http://oldetoolshop.com/forsale/june/earlywigiron0601b.jpg
http://oldetoolshop.com/forsale/june/earlywigiron0601c.jpg
http://oldetoolshop.com/forsale/june/earlywigiron0601d.jpg
http://oldetoolshop.com/forsale/june/earlywigiron0601e.jpg
New Britain No H-3-1 3 1/2 Oz Ball Penn Hammer. Measuring 10 9/16"
overall, the head is 2 9/16" long, the face is 11/16" in diameter, the
peen is 11/16" in diameter, and this weighs 7 oz total unboxed. This is
in reasonably good condition and was cleaned. The head has some
frosting, but nothing too bad patina wise. The face also has some light
patina and a few very light dings. The handle is original and is good
save for some wear to the finish. This ain't minty, but it will get the
job done. $24.00
http://oldetoolshop.com/forsale/june/hammer0605a.jpg
http://oldetoolshop.com/forsale/june/hammer0605b.jpg
http://oldetoolshop.com/forsale/june/hammer0605c.jpg
http://oldetoolshop.com/forsale/june/hammer0605d.jpg
Vintage Small Cobblers Hammer. Measuring 8 3/4" overall, the head is 3
1/2" long, the face is 1 1/4" in diameter, the peen is 1 1/4" wide, and
this weighs 13 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. The sides and around the eye
was never finished off real pretty like. The face has some dings and
wear. The peen also has some dings. The handle is good other than a
few light dings and stains. This ain't got a fancy maker's mark, but it
will get the job done. $18.00
http://oldetoolshop.com/forsale/june/hammer0606a.jpg
http://oldetoolshop.com/forsale/june/hammer0606b.jpg
http://oldetoolshop.com/forsale/june/hammer0606c.jpg
http://oldetoolshop.com/forsale/june/hammer0606d.jpg
Blacksmith Engineer Style 2 lb Straight Peen Hammer. Measuring 15 1/2"
overall, the head is 5 1/4" long, the face is 1 3/8" in diameter, the
peen is 1 5/16" in diameter, and this weighs 2 lbs 4 1/2 oz unboxed.
Not signed as to the maker. This is in reasonably good condition and
was cleaned. Somebody else did the paint job on the head and there is a
user initial pin punched on the one side. The face has some wear around
the edge and some light dings and patina. The peen was dressed at some
point, but is good. The handle is good overall and the head is on
tight, at least sitting here. I gotta say, that these guys are sure
getting few and far between any more. $30.00
http://oldetoolshop.com/forsale/june/hammer0607a.jpg
http://oldetoolshop.com/forsale/june/hammer0607b.jpg
http://oldetoolshop.com/forsale/june/hammer0607c.jpg
http://oldetoolshop.com/forsale/june/hammer0607d.jpg
Dixon Jewelers Hand Vise Or Handvise. Measuring 4 5/16" long, the jaws
are 1/4" wide, and this weighs 1 1/2 oz unboxed. This is in decent
condition and was cleaned. The jaws have some light pitting on the tops
and some frosting on the sides. The faces are good. Both jaws move, but
are a little slow. The screw is good. The handle has some wear and a
little staining. That is hollow all the way through to the jaws. This
ain't pristine, but it is a quality tool that will get the job done. $28.00
http://oldetoolshop.com/forsale/june/handvise0602a.jpg
http://oldetoolshop.com/forsale/june/handvise0602b.jpg
http://oldetoolshop.com/forsale/june/handvise0602c.jpg
Hand Forged Early Farriers Clinch Block Anvil. Measuring 4 3/16" long,
the face is 2" by 1 15/16", and this weighs 9 oz unboxed. Not signed as
to the maker. This is in fair condition and was cleaned. Needless to
say, this guy spent a lot of time out in the barn and weather. There is
some overall pitting. The tip of the handle has some roughness from
pitting as well. This ain't pretty or perfect, but these older ones are
sure getting few and far between any more. $25.00
http://oldetoolshop.com/forsale/june/hfclinchblock0601a.jpg
http://oldetoolshop.com/forsale/june/hfclinchblock0601b.jpg
http://oldetoolshop.com/forsale/june/hfclinchblock0601c.jpg
http://oldetoolshop.com/forsale/june/hfclinchblock0601d.jpg
Harold M Pitman Solid Brass Folding Jewelers Loupe. Measuring 1 3/16"
bu 1 1/4" square, 1/4" high with closed, and this weighs 1 oz unboxed.
Made in Germany. This is in reasonably good condition and was cleaned.
The outsides are good as is the glass. The insides have a little funky
that refused to come off. The springs and hinges are good and the catch
works. This ain't pristine, but it is a neat tool that will get the job
done. $30.00
http://oldetoolshop.com/forsale/june/jewelerstool0601a.jpg
http://oldetoolshop.com/forsale/june/jewelerstool0601b.jpg
http://oldetoolshop.com/forsale/june/jewelerstool0601c.jpg
http://oldetoolshop.com/forsale/june/jewelerstool0601d.jpg
Small Vintage Specialty User Crafted Knife Awl. Measuring 5 1/4"
overall, the blade is 2 1/8" long, 7/16" wide at the start of the
handle, and this weighs 1 oz unboxed. Not signed as to the maker. This
is in decent condition and was cleaned. The blade has some light patina
and some scuffs. The tip is missing a wee bit and the edge for the
first 1/2 is a bit dull, after that it's not too bad. The black walnut
handle was hand craved and is in good shape save for a few light dings.
This is what it is, but it is a neat tool to say the least. $14.00
http://oldetoolshop.com/forsale/june/knife0601a.jpg
http://oldetoolshop.com/forsale/june/knife0601b.jpg
http://oldetoolshop.com/forsale/june/knife0601c.jpg
C S Osborne No 151 1/2 Inch Bag Or Oblong Punch. Measuring 4 13/16"
long and this weighs 3 1/4 oz unboxed. This is in decent condition and
was cleaned. There is some wear to the finish. The edge is a bit
dinged up, that feels sort of sharp to the touch, but it will need some
work. The striking end has the start of some mushrooming. This ain't
minty, but if that's what you want, well new ones are like 3 times what
I'm asking for this one. Just saying. $20.00
http://oldetoolshop.com/forsale/june/leathertool0601a.jpg
http://oldetoolshop.com/forsale/june/leathertool0601b.jpg
http://oldetoolshop.com/forsale/june/leathertool0601c.jpg
Vintage Red Devil No PI-2F Putty Knife With Rosewood Handle. Measuring 7
1/4" long, 2" wide across the edge, and this weighs 2 1/2 oz unboxed.
This is in reasonably good condition and was cleaned. The blade has
some light scratches and a few spots of frosting, but nothing too bad.
The handle scales are rosewood, the one has some nice color to it, the
other one is on the blonde side. Both have some tiny bits of paint down
in the grain and a few light dings, but they are solid and on tight.
This ain't pristine, but it will get the job done. $15.00
http://oldetoolshop.com/forsale/june/paintscraper0601a.jpg
http://oldetoolshop.com/forsale/june/paintscraper0601b.jpg
http://oldetoolshop.com/forsale/june/paintscraper0601c.jpg
Long G A Dard Wood Handle Turnscrew Or Screwdriver. Measuring 14 1/2"
long, the tip is 3/8" wide, and this weighs 8 1/4 oz unboxed. Nothing
shows up for this maker. This is in decent condition and was cleaned.
There are some overall dots of light pitting on the blade and some dings
on the sides. The tip has some wear. I can't say what kind of wood the
handle is. That has some dings and stains, and there is some roughness
and a few small chips on the end, but overall it's solid. This ain't
minty, but it will get the job done. $20.00
http://oldetoolshop.com/forsale/june/turnscrew0602a.jpg
http://oldetoolshop.com/forsale/june/turnscrew0602b.jpg
http://oldetoolshop.com/forsale/june/turnscrew0602c.jpg
Blacksmith Hand Forged 20 Inch Universal Jaw Tongs. Measuring 20 1/2"
long, the jaws are 2" deep, 7/16" wide at the tips, and this weighs 2
lbs 2 oz unboxed. Not signed as to the maker. This is in good
condition and was cleaned. There is some overall light patina. The
jaws are good and close down tight. They are grooved at the tips. THe
joint is good with just a hair of wiggle. This is a handy tool to say
the least. $22.00
http://oldetoolshop.com/forsale/june/blacksmith0609a.jpg
http://oldetoolshop.com/forsale/june/blacksmith0609b.jpg
http://oldetoolshop.com/forsale/june/blacksmith0609c.jpg
http://oldetoolshop.com/forsale/june/blacksmith0609d.jpg
L S Starrett No 467RL 1 Inch Micrometer Caliper & Box. This weighs 6
3/4 oz unboxed. This is in good condition and was not cleaned. The
finish on the head is perfect. There is a little light patina on the
name plates on the head. The handle is clean and all the markings are
readable. The box has some light wear. This also includes the wrench,
which does have some light patina, the owner's manual, and a Starrett
reference card. This ain't perfect, but for being a used tool, it's
pretty dang close. $18.00
http://oldetoolshop.com/forsale/june/machinesttool0609a.jpg
http://oldetoolshop.com/forsale/june/machinesttool0609b.jpg
http://oldetoolshop.com/forsale/june/machinesttool0609c.jpg
http://oldetoolshop.com/forsale/june/machinesttool0609d.jpg
Stanley No 25 6 Inch Adjustable Bevel Square. This weighs 3 oz
unboxed. This is in good condition, it had been cleaned by someone else
and I just did some detailing on it. The blade has some light frosting
around the slot, but overall nothing too bad. The edges and corners are
good. The rosewood handle is also good, save for a user initial B
scratched on the one end plate and the same initial carved on the end.
The locking screw and nut work. This ain't pristine, but it sure ain't
bad, and it will get the job done. $22.00
http://oldetoolshop.com/forsale/june/square0602a.jpg
http://oldetoolshop.com/forsale/june/square0602b.jpg
http://oldetoolshop.com/forsale/june/square0602c.jpg
http://oldetoolshop.com/forsale/june/square0602d.jpg
Small Hand Forged Blacksmith Tongs. Measuring 10 7/8" long, the jaws
are 1 7/16" deep, 3/16" wide at the tips, and this weighs 4 1/2 oz
unboxed. Not signed as to the maker. This is in good condition and was
lightly cleaned. The one arm was forged from a file, you see a little
of the teeth around the joint. The jaws are good. The joint has a
little wiggle. This ain't for knocking out horse shoes, but for doing
small detail work, it will get the job done. $20.00
http://oldetoolshop.com/forsale/june/blacksmith0603a.jpg
http://oldetoolshop.com/forsale/june/blacksmith0603b.jpg
http://oldetoolshop.com/forsale/june/blacksmith0603c.jpg
http://oldetoolshop.com/forsale/june/blacksmith0603d.jpg
Unusual Bent Tip Small Hand Forged Blacksmith Tongs. Measuring 8 5/8"
long, the jaws are 2 1/4" deep, 3/16" wide at the tips, and this weighs
9 1/2 oz unboxed. Not signed as to the maker. This is in good
condition and was cleaned. There ain't much in the way of patina
overall. The tips are good. The joint is good with just a wee bit of
wiggle. I ain't sure what this is used for, but somebody, someplace,
must have needed it. $22.00
http://oldetoolshop.com/forsale/june/blacksmith0604a.jpg
http://oldetoolshop.com/forsale/june/blacksmith0604b.jpg
http://oldetoolshop.com/forsale/june/blacksmith0604c.jpg
http://oldetoolshop.com/forsale/june/blacksmith0604d.jpg
Blacksmith Hand Forged Hot Cold Cut Chisel. Measuring 10 1/2" overall,
the head is 6 1/8" long, the edge is 1 5/16" high, and this weighs 2 lbs
12 oz unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. There ain't much in the way of patina on the
head, save for some user initials chisel marked on both sides. The edge
isn't bad, but could stand a touch up. There is a little mushrooming on
the striking end and I did drag a file over some sharp spots. The
square punched eye looks to be good. The handle has some roughness
under the eye, some dings, stains, and some mushrooming at the end, but
will get the job done, until it don't. This is a good looking old tool
to say the least. $22.00
http://oldetoolshop.com/forsale/june/blacksmith0605a.jpg
http://oldetoolshop.com/forsale/june/blacksmith0605b.jpg
http://oldetoolshop.com/forsale/june/blacksmith0605c.jpg
http://oldetoolshop.com/forsale/june/blacksmith0605d.jpg
Vintage Hand Forged 1/2 lb Cross Peen Hammer. Measuring 12 1/8"
overall, the head is 4 3/16" long, the face is 1/2" square, the peen is
7/8" wide, and this weighs 10 1/2 oz total unboxed. Not signed as to
the maker. This is in decent condition and was cleaned. There are some
scuffs on the head left over from when this was forged and some light
dings and patina. THe face has some tiny dings. The peen has some wear
to the one side and is setting at a little bit of an angle. The handle
has some chipping under the eye, some dings and stains, and some
chipping at the end. But it feels solid enough and the head is on tight
thanks to a big old wood screw in from the top. This ain't minty, but
it is an older tool that will get the job done. $20.00
http://oldetoolshop.com/forsale/june/hammer0602a.jpg
http://oldetoolshop.com/forsale/june/hammer0602b.jpg
http://oldetoolshop.com/forsale/june/hammer0602c.jpg
L S Starrett No 564 Universal Junior Machinist Indicator Set & Box.
This all weighs 5 1/2 oz unboxed. This is in good condition and was not
cleaned. There ain't nothing much at all to fuss about with the tool
and parts. The head works like it should. The box has some wear, but
it's solid. This is a quality tool to say the least. $35.00
http://oldetoolshop.com/forsale/june/machinesttool0602a.jpg
http://oldetoolshop.com/forsale/june/machinesttool0602b.jpg
http://oldetoolshop.com/forsale/june/machinesttool0602c.jpg
http://oldetoolshop.com/forsale/june/machinesttool0602d.jpg
http://oldetoolshop.com/forsale/june/machinesttool0602e.jpg
L S Starrett No 45 A Machinist Depth Gage. This weighs 1 1/2 oz
unboxed. This has one of the earlier Starrett marks (before 1910 if I
remember correctly). This is in decent condition and was cleaned.
There is some frosting and light patina on both sides of the head. The
edges are good. The rod is good as well and the screw works and holds.
This ain't pristine, but it's a quality and older tool that will get the
job done. $17.00
http://oldetoolshop.com/forsale/june/machinesttool0601a.jpg
http://oldetoolshop.com/forsale/june/machinesttool0601b.jpg
http://oldetoolshop.com/forsale/june/machinesttool0601c.jpg
Snell & Atherton Star Logo No 87 1/2 Cobblers Creasing Seaming Tool.
Measuring 6 1/2" long, the head is 1 1/8" wide, 1/2" thick, and this
weighs 3 1/2 oz unboxed. This is in reasonably good condition and was
cleaned. The head is good other than some frosting and a little wear to
the center divider, but the face is clean. The handle is original and
has a little wear to the finish, but it's solid. This is a good looking
tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/may/leathertool0504a.jpg
http://oldetoolshop.com/forsale/may/leathertool0504b.jpg
http://oldetoolshop.com/forsale/may/leathertool0504c.jpg
http://oldetoolshop.com/forsale/may/leathertool0504d.jpg
Signed Vintage Wooden Spoke Shave Or Spokeshave. Measuring 10 3/8"
overall, the blade is 2 11/16" long, a little over 9/16" wide across the
edge, and this weighs 3 3/4 oz unboxed. This is in decent condition and
was cleaned. There is some overall staining on the body and a few
dings. There is some wear to the sole in front of the mouth. The blade
has some frosting, but nothing too bad. There are some tiny chips on
the edge. The blade does remove and holds position. This ain't minty,
but it will get the job done. $20.00
http://oldetoolshop.com/forsale/may/spokeshave0503a.jpg
http://oldetoolshop.com/forsale/may/spokeshave0503b.jpg
http://oldetoolshop.com/forsale/may/spokeshave0503c.jpg
Vintage Small Iron Body Spoke Shave Or Spokeshave. Measuring 8 9/16"
long, the blade is 1 11/16" wide, and this weighs 6 3/4 oz unboxed. Not
signed as to the maker. This is in decent condition and was cleaned.
The finish on the body is pretty much gone. The sole has some frosting
and spots of light pitting. The blade also has some frosting and some
dots of light pitting. The edge is slightly convex, but is fairly
good. The screw works and was oiled. This ain't pretty or perfect, but
it will get the job done. $17.00
http://oldetoolshop.com/forsale/may/spokeshave0502a.jpg
http://oldetoolshop.com/forsale/may/spokeshave0502b.jpg
http://oldetoolshop.com/forsale/may/spokeshave0502c.jpg
http://oldetoolshop.com/forsale/may/spokeshave0502d.jpg
THREE C D Dickinson & Son Specialty Double End Center Hole Needles.
They are 7 3/16" long, a little under 5/16" wide at the centers, and
they weigh 2 oz unboxed. These are in reasonably good condition and
were cleaned. There is some staining and a little frosting, but nothing
too bad. The tips are good to go. These ain't minty, but they are
older tools that will get the job done. $15.00
http://oldetoolshop.com/forsale/may/leathertool0501a.jpg
http://oldetoolshop.com/forsale/may/leathertool0501b.jpg
http://oldetoolshop.com/forsale/may/leathertool0501c.jpg
http://oldetoolshop.com/forsale/may/leathertool0501d.jpg
Blacksmith Hand Forged 2 Inch Flatter Hammer. Measuring 12 3/8"
overall, the head is 4 11/16" long, the face is 2 1/16" wide, 2" high,
and this here pup weighs 5 lbs 2 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. Uh huh. There is
lots of patina going on the head, including some light pitting, punch
marks, dings, chisel marks, etc. The face has some cut marks or
scratches along with some dings and wear. I did run a file over that to
tone things down a little, but it's gonna take something with a bit more
horsepower to make it right. The striking end had some mushrooming
dressed and hammered down at some point and that is good to go. The
handle could be black walnut. That has some nice decorative work to it,
along with some dings, and some chipping at the end, but it's solid.
This ain't pristine, but there ain't much in life that is these days,
and this guy will get the job done. $35.00
http://oldetoolshop.com/forsale/may/blacksmith0503a.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503b.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503c.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503d.jpg
http://oldetoolshop.com/forsale/may/blacksmith0503e.jpg
Vintage Solid Brass 5 Inch Outside Caliper. Measuring 5 1/16" long and
this weighs 2 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. There are some light dings
and scuffs, but nothing too bad. The joint is good and holds position
and the tips are ready to work. This is a good looking older tool that
will get the job done. $18.00
http://oldetoolshop.com/forsale/may/divider0505a.jpg
http://oldetoolshop.com/forsale/may/divider0505b.jpg
http://oldetoolshop.com/forsale/may/divider0505c.jpg
R Timmins & Sons No 00 Cobbler Lasting Pliers. Measuring 6 3/4" long,
the jaws are 3/8" wide at the tips, and this weighs 7 oz unboxed. R
Timmins & Sons were 19th Century Birmingham England tool makers who were
in business until the 1870's when they merged with the Wynn company.
This is in reasonably good condition and was cleaned. There is a little
frosting and patina overall. The jaws to have some wear to the teeth,
but they close down tight. The "through the center" joint does have a
little play. The hammer poll has some dings, and some chipping and a
little mushrooming down at the bottom. There is a little roughness at
the ends of both handles. There is no tack claw, but this size tool
rarely had them. This ain't minty, but these smaller ones sure ain't
getting any easier to find and seeing as how this guy is at least 150
years old and probably older, well it sure ain't bad. $27.00
http://oldetoolshop.com/forsale/may/leathertool0505a.jpg
http://oldetoolshop.com/forsale/may/leathertool0505b.jpg
http://oldetoolshop.com/forsale/may/leathertool0505c.jpg
http://oldetoolshop.com/forsale/may/leathertool0505d.jpg
Sargent & Co Cast Steel Hewing Hatchet Broad Axe. Measuring 18"
overall, the head is 6 3/4" long (across the center), the edge is 5
13/16" high (straight across), and this weighs 3 lbs 1 1/4 oz unboxed.
This is in reasonably good condition and was cleaned. The head has some
spots of light patina including some dings. The steel bit is about 7/8"
deep and is good save for some pin-point pitting. The edge will need a
quick touch up. The poll has some dings. The eye looks to be good with
no cracks that I can see. The oval shaped handle is original and good.
There is a small strap hole at the end and somebody put a small piece of
metal at the back of the eye. There also are some spots of blue paint at
the end and around the eye that refused to come off. This ain't
pristine, but it sure ain't bad for being 125 or so years old, and it
will get the job done. $75,00
http://oldetoolshop.com/forsale/may/axe00502a.jpg
http://oldetoolshop.com/forsale/may/axe00502b.jpg
http://oldetoolshop.com/forsale/may/axe00502c.jpg
http://oldetoolshop.com/forsale/may/axe00502d.jpg
http://oldetoolshop.com/forsale/may/axe00502e.jpg
Hand Forged 7 Oz Cross Peen Hammer. Measuring 8 1/16" overall, the head
is 4 13/16" long, the face is 7/16" square, the peen is 15/16" wide, and
this weighs 7 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall light pitting and
patina on the head. The face and peen also have some light stuff, but
nothing too bad. The square punched eye has a little crusty on the
inside, but it's solid. The handle is old and could be the original
one. That has some stains and dings, but it's fairly solid. The head
does set at a little bit of an angle. This ain't pretty or perfect, but
it will get the job done. $20-.00
http://oldetoolshop.com/forsale/may/hammer0503a.jpg
http://oldetoolshop.com/forsale/may/hammer0503b.jpg
http://oldetoolshop.com/forsale/may/hammer0503c.jpg
http://oldetoolshop.com/forsale/may/hammer0503d.jpg
P S & W 8 Inch Folding Handle Draw Knife Or Drawknife. Measuring 15 3/8"
overall, the blade is 8" long, 1 3/8" wide at the center 1 5/16" at the
ends, and this weighs 1 lb 4 3/4 oz unboxed. This is in reasonably good
condition and was cleaned. There is some frosting on the steel area of
the back, but nothing too bad. The iron frame and the front also has
some frosting. The edge will need a little touch up. The top is good
and was never struck. Both handles have some dings, stains, and a
little wear, but they have most of the original finish plus a coat of
wax. Note: They are not notched to protect the edge. The nuts are good
and hold. This ain't minty, but for the age, it sure ain't bad, and it
is a top quality tool that will get the job done. $65.00
http://oldetoolshop.com/forsale/may/drawknife0501a.jpg
http://oldetoolshop.com/forsale/may/drawknife0501b.jpg
http://oldetoolshop.com/forsale/may/drawknife0501c.jpg
http://oldetoolshop.com/forsale/may/drawknife0501d.jpg
Small Hand Forged Straight Jaw Blacksmith Tongs. Measuring 9 3/8" long,
the jaws are 2 7/8" deep, 3/8" wide at the tips, and this weighs 6 1/2
oz unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. There is the usual patina, but nothing too
bad. The jaws and handles are good. The joint has a little wiggle, but
the rivet is solid. This ain't for knocking out horseshoes, but for the
small jobs it will do just fine. $19.00
http://oldetoolshop.com/forsale/may/blacksmith0502a.jpg
http://oldetoolshop.com/forsale/may/blacksmith0502b.jpg
http://oldetoolshop.com/forsale/may/blacksmith0502c.jpg
http://oldetoolshop.com/forsale/may/blacksmith0502d.jpg
L S Starrett No 166 A Machinist Pin Vise. This weighs 1/4 oz unboxed.
This is in good condition and was cleaned. There ain't nothing much
patina wise on this guy. The chuck and jaws are good. The handle does
have a shop and user name lightly scratched on it, but otherwise that is
good as well. This ain't perfect, but it will get the job done. $15.00
http://oldetoolshop.com/forsale/may/machinisttool0502a.jpg
http://oldetoolshop.com/forsale/may/machinisttool0502b.jpg
Vintage Lancashire Pattern 3 Inch Outside Caliper. Measuring 3 7/16"
long and this weighs 3/4 oz unboxed. Not signed as to the maker. This
is in decent condition and was cleaned. There is some overall light
pitting and patina. The spring and tips are good. The screw threads are
good and the nut travels the full distance. That was oiled. This ain't
perfect, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/may/divider0501a.jpg
http://oldetoolshop.com/forsale/may/divider0501b.jpg
http://oldetoolshop.com/forsale/may/divider0501c.jpg
Zomax USA 6 Ft Wood Zig Zag Rule. This weighs 3 3/4 oz unboxed. This is
in like new condition and was not cleaned. There just ain't nothing at
all to fuss about with this guy. The finish is good all around. The
segments are all straight and the joints are all good. This is about as
good as one of these guys gets. $16.00
http://oldetoolshop.com/forsale/may/rule0502a.jpg
http://oldetoolshop.com/forsale/may/rule0502b.jpg
http://oldetoolshop.com/forsale/may/rule0502c.jpg
http://oldetoolshop.com/forsale/may/rule0502d.jpg
P S Stubs No 14 Jewelers Pliers. Measuring 4 5/16" long, the jaws are
5/8" deep, 5/32" wide at the tips, and this weighs 1 1/4 oz unboxed.
This is in reasonably good condition and was cleaned. There is a little
frosting and staining, but nothing too bad. The jaws are good save for
a little wear on the tips and they close up tight and flush. The
"through the center" style joint has a wee bit of wiggle to it. This
ain't perfect, but it is a top quality tool that will get the job done.
$17.00
http://oldetoolshop.com/forsale/april/pliers0401a.jpg
http://oldetoolshop.com/forsale/april/pliers0401b.jpg
http://oldetoolshop.com/forsale/april/pliers0401c.jpg
TWO L S Starrett No 470 Framing Square Stair Fixture Guides. They weigh
2 oz unboxed. These are in reasonably good condition and were cleaned.
The bodies have some dots of light patina and there is a little funky on
the inside of the grooves. Both screws are good to go. These are handy
and top quality tools to have around. $22.00
http://oldetoolshop.com/forsale/april/squareguides0401a.jpg
http://oldetoolshop.com/forsale/april/squareguides0401b.jpg
http://oldetoolshop.com/forsale/april/squareguides0401c.jpg
Hand Forged Early Eel Or Frog Gig. Measuring 15 5/8" overall, the head
is 4 1/16" long, 2 1/16" wide across the outside of the tips, and this
weighs 8 1/2 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. There is some overall light
patina. The head is good, and the hand cut barbs on the insides of the
outer tines are sharp. This will need a handle, but that's an easy
fix. I gotta say, that these guys are sure few and far between of
late. $30.00
http://oldetoolshop.com/forsale/april/hfeelgig0401a.jpg
http://oldetoolshop.com/forsale/april/hfeelgig0401b.jpg
http://oldetoolshop.com/forsale/april/hfeelgig0401c.jpg
http://oldetoolshop.com/forsale/april/hfeelgig0401d.jpg
Goodell-Pratt No 514 4 Inch Machinist Divider. Measuring 4 13/16" long
(from the tips to the top of the spring) and this weighs 1 1/2 oz
unboxed. This is in reasonably good condition and was cleaned. There is
a little frosting on the legs. The joint is good other than a little
crusty on the inside and the tips are quite pointy (yeah I found that
out the hard way!) The nut travels the full distance and was oiled.
This ain't minty, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/april/machinisttool0409a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0409b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0409c.jpg
Moore & Wright Sheffield 4 Inch Machinist Try Square. Measuring 3
15/16" overall in length, the blade is 3 3/16" long, 2 5/8" high, and
this weighs 3 1/2 oz unboxed. This is in good condition and was
cleaned. The blade has some light scuffs and a little frosting, but
nothing too bad. The handle also has some frosting and a user mark on
the back side. All of the edges and corners are crispy good. This ain't
minty, but it is a quality tool that will get the job done. $24.00
http://oldetoolshop.com/forsale/april/machinisttool0410a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0410b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0410c.jpg
http://oldetoolshop.com/forsale/april/machinisttool0410d.jpg
Uncommon Starrett No 61 Reliable Try Square. The blade is 4" long and
this weighs 2 3/4 oz unboxed. This is in reasonably good condition and
was cleaned. The blade has some light scuffs and some frosting on the
front and some very light rust etching and a small user mark on the
back. The edges and corners are good. The handle finish is original,
but is worn a little. The machined faces have some frosting, a couple
of dings, and scuffs, but nothing too bad. The locking nut works and was
oiled. This ain't pristine, but this is not a very common Starrett tool
to say the least, and a new one will cost close to twice what I'm asking
for this one. $85.00
http://oldetoolshop.com/forsale/april/machinisttool0406a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0406b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0406c.jpg
http://oldetoolshop.com/forsale/april/machinisttool0406d.jpg
http://oldetoolshop.com/forsale/april/machinisttool0406e.jpg
Unusual Hand Forged Blacksmith Top Swage Head. Measuring 5 5/8" long,
the face are is 3 1/16" wide (across the outside), 1 11/16" thick, 2
1/4" on the inside, 1 1/4" deep, and this weighs 2 lbs 10 1/2 oz
unboxed. Not signed as to the maker. What this is for, I ain't gotta
clue, and my local expert don't either. Do not make this a guessing
game, PM me with any thoughts. This is in decent condition and was
cleaned. There is some overall light patina. The face has some dings
and a little mushrooming on the outside of the one edge. The striking
end has some checks and the start of some flaking in the center. The
eye is solid with no checks, but it wasn't the world's greatest punch
job either. This ain't perfect, but it ain't like another one will be
showing up any time soon. $27.00
http://oldetoolshop.com/forsale/april/blacksmith0401a.jpg
http://oldetoolshop.com/forsale/april/blacksmith0401b.jpg
http://oldetoolshop.com/forsale/april/blacksmith0401c.jpg
http://oldetoolshop.com/forsale/april/blacksmith0401d.jpg
James Swan Coopers Bung Auger. Measuring 13 3/4" long, the cut is 2" in
diameter, and this weighs 1 lb 11 1/2 oz unboxed. This is in reasonably
good condition and was cleaned. There is some overall frosting on the
head. The lead screw and cutters are good. The rulings are readable on
side of the auger. The cutting edge is fairly good. The handle is
good, save for a few tiny dots of paint, and has almost all of the
original finish. The screw doesn't remove. This ain't pristine, but
these guys are sure getting few and far between these days. $40.00
http://oldetoolshop.com/forsale/april/cooperstool0401a.jpg
http://oldetoolshop.com/forsale/april/cooperstool0401b.jpg
http://oldetoolshop.com/forsale/april/cooperstool0401c.jpg
http://oldetoolshop.com/forsale/april/cooperstool0401d.jpg
Owasgo Tool No 217 5/8 Inch Side Bead Molding Plane. This weighs 15 1/2
oz unboxed. Owasco Tool Co was a brand name used by the Auburn Tool
Co. This is in good condition and was cleaned. The body has a few
stains, a E scratched on the back, and a couple of very thin checks on
the toe and heel. The sole and boxing are good and the mouth is factory
tight. The wedge is also good. The iron has a few dots of light
patina, but it's clean for the most part. This ain't pristine, but it's
a solid tool that will get the job done. $20.00
http://oldetoolshop.com/forsale/april/woodenplane0406a.jpg
http://oldetoolshop.com/forsale/april/woodenplane0406b.jpg
http://oldetoolshop.com/forsale/april/woodenplane0406c.jpg
http://oldetoolshop.com/forsale/april/woodenplane0406d.jpg
SEVEN G I Mix No 1 EX Paring Bevel Side Chisels. There is a 3/4",
measuring 8 13/16" from the edge to the end of the socket, the blade is
6 1/8" long, a 7/8", measuring 9 3/16" from the edge to the end of the
socket, the blade is 6 1/8" long, a 1", measuring 9 1/16" from the edge
to the end of the socket, the blade is 6 1/8" long, a 1 1/4", measuring
9 1/2" from the edge to the end of the socket, the blade is 6" long, a 1
1/2", measuring 10 1/8" from the edge to the end of the socket, the
blade is 6 3/16" long, a 1 3/4", measuring 10 1/8" from the edge to the
end of the socket, the blade is 6 1/4" long, a 2", measuring 10 1/8"
from the edge to the end of the socket, the blade is 6 1/4" long, and
they weigh 4 lbs 5 oz unboxed. These are in reasonably good condition
and were cleaned. The backs have a few spots of very light pitting,
along with some staining and frosting, but overall nothing too bad. The
tops have more of the same. The edges are fairly good, but will need a
little work. I did take off a little sharp mushrooming off of a couple
of the sockets, and the one is a little funky on the inside where
somebody else got aggressive removing an old handle, but they are good.
These will need handles, I've tried to get a nice matching set together
with no luck. These ain't pristine, but they sure ain't bad, and sets
like this are getting few and very far between of late. The price
includes US Priority Mail Shipping with insurance and signature
confirmation. $375.00
http://oldetoolshop.com/forsale/april/chiselset0401a.jpg
http://oldetoolshop.com/forsale/april/chiselset0401b.jpg
http://oldetoolshop.com/forsale/april/chiselset0401c.jpg
http://oldetoolshop.com/forsale/april/chiselset0401d.jpg
http://oldetoolshop.com/forsale/april/chiselset0401e.jpg
http://oldetoolshop.com/forsale/april/chiselset0401f.jpg
Kinex DIN 875/0 4 Inch Machinist Square. Measuring 5 1/8" overall in
length, the blade is 4 1/16" long, 3 3/32" high, and this weighs 8 oz
unboxed. This is in very good condition and was not cleaned. There are
some light scuffs and a few dots of light patina, but nothing too bad.
The edges and corners are crispy good. This is a quality tool and
priced cheaper than what a new one will run you. $30.00
http://oldetoolshop.com/forsale/april/machinisttool0405a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0405b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0405c.jpg
Unusual Long Wood Model Makers Clamp. The body is 15 7/8" overall, the
clamping area is 13 1/2" long, the throat is 1/2", the holes for the
movable jaw are spaced at 7/8", and this weighs 3 1/2 oz unboxed. Not
signed as to the maker. This is in reasonably good condition and was
cleaned. There are some light dings and stains, but nothing too bad.
The screw travels the full distance. All the holes are clear. This is
a neat clamp for doing light work to say the least. $24.00
http://oldetoolshop.com/forsale/april/clamp0402a.jpg
http://oldetoolshop.com/forsale/april/clamp0402b.jpg
http://oldetoolshop.com/forsale/april/clamp0402c.jpg
Lufkin Rule No 513 Micrometer Depth Gage With Orig Box. This all weighs
1 lb unboxed. John A. Schleicher of Saginaw, MI was granted Pat. No.
1,424,383 on Aug. 1, 1922 and Pat. No. 1,568,295 on Jan. 5, 1926 for the
design of this tool. This is in good condition and was not cleaned.
The head is clean save for some very light scratches on the face and
some light scuffs on the back. The micrometer turns smoothly and the
cap nut for the rods works. This has 3 rods total (one in the tool and
2 in the box). They have a little wear on the sides, but nothing too
bad. This also has the wrench. The oak box has some dings and light
stains, but it's solid, and the late works. This ain't pristine, but it
will get the job done. $45.00
http://oldetoolshop.com/forsale/april/machinisttool0403a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403c.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403d.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403e.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403f.jpg
--------------------------------------------------------
"Difficulties strengthen the mind as labor does the body."
Seneca
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
|
