OldTools Archive
Recent | Bios | FAQ |
160812 | "Christian A. Weagle" <cweagle@i...> | 2006‑06‑04 | Introduction, Millers Falls No. 16 |
Hello all, I have been lurking for some time but this is my first posting. I should introduce myself. There is tool-related content below, please feel free to skip to it if you'd like; there will not be a quiz. I am a relatively young electrical engineer, building robots for a living. While i was in school, I spent a lot of time working in machine shops, building things with my hands. My current occupation has me behind a desk most of the time, and I missed the feel of physically creating. I had built a few bookcases and the like, in school, and liked the feel of wood - very 'analog' compared to the 'digital' of metal (though both have their times and places). I am part way into a few projects now, having accumulated a few basic hand tools. So: My initial efforts planing the end grain of some boards with my large wooden fore plane were met with limited sucess (I will build a shooting board... someday). I had the opertunity to buy a block plane - a Millers Falls No. 16 (= Stanley No. 9 1/2) that seemed in OK shape - it was a good price anyway. The first thing I found was that the two prongs on the vertical adjuster yoke were worn down enough that moveing them had little effect on the actual blade. A little grinder time made a serviceable replacement. But now, after sharpening the (initially very dull) blade, I have found the terrible truth of this plane - it's too short! It just makes it to the mouth, but does not extend at all. It is bottomed out against the round stop on the lateral adjuster. I see that some new replacements are available, but they appear to all cost several times what I paid for the plane in the first place! Would it be considered unwise to, ahh, lengthen the slot a bit (say, 1/8") with a dremel or the like? I can't imagine I'd run out of hardened blade in that distance, right? Or: is there a source of very cheap, good quality blades I don't yet know about? ------------------------------------------------------------------------ |
|||
160816 | Steve Reynolds <s.e.reynolds@v...> | 2006‑06‑04 | Re: Introduction, Millers Falls No. 16 |
On Jun 4, 2006, at 1:50 PM, Christian A. Weagle wrote: Welcome to the Porch, Christian. I commend you on selecting the brand of plane that distinguishing cabinetmakers choose. Millers "No. 2 Tried Harder" Falls. > But now, after sharpening the (initially very dull) blade, I have > found the terrible truth of this plane - it's too short! It just > makes it to the mouth, but does not extend at all. It is bottomed out > against the round stop on the lateral adjuster. I see that some new > replacements are available, but they appear to all cost several times > what I paid for the plane in the first place! Would it be considered > unwise to, ahh, lengthen the slot a bit (say, 1/8") with a dremel or > the like? I can't imagine I'd run out of hardened blade in that > distance, right? > I did this a couple of weeks ago, and it worked well. My first attempt was to use a Dremel with some sorta spiked milling type bit. No joy. I then used a bastard file and it went quickly and allowed for a lot of control over the cutting. I suggest you start here. There is plenty of hardened steel in most block plane blades (perhaps the whole shebang?) so you should not run short. > Or: is there a source of very cheap, good quality blades I don't yet > know about? > > I could get ugly looks from some corners of the Porch for saying this, but the Buck Bros blades sold in the Borg for cheap aren't all crap. They are partly crap for the hardness they are tempered to, but a young EE should be able to have a lot of hands-on physical fun in playing with fire and oil while retempering it. Regards, Steve ------------------------------------------------------------------------ |
|||
160870 | "Walt Cheever" <waltc@m...> | 2006‑06‑05 | Re: Introduction, Millers Falls No. 16 |
Welcome aboard Chris!!! No matter what, there is an inherent satisfaction about making something with your own two hands, with little tool help. I seriously doubt that extending the slot in the plane blade will count as defacing our mutual endowment of old tools. And it must work, I have two block planes that have been similarly altered. Walt C ------------------------------------------------------------------------ |
|||
Recent | Bios | FAQ |